This patch finishes cx88-blackbird conversion to use video_ioctl2. Video
standards are generated automatically inside videodev.c. the big ioctl
parser is removed, using, instead, video_ioctl2.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
v4l2_tvnorm were meant to describe video standards and its names to V4L2 API.
However, this were doing by some static structures at the driver.
This patch changes the internals in a way that, at the driver, only a
v4l2_tvnorm (a 64 bit integer) should be filled, with all supported
tvnorms. videodev will dynamically generate the proper API array
based on supported standards.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
video_ioctl2 handler provides V4L2 API parsing.
Using it makes the driver simpler, and isolates API parsing.
This allows future reusage of driver controls using other ways, like sysfs
and/or procfs and increases isolation of driver-specific handling from the
generic common ioctl processing.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
With the previous patch, mplayer started but was polling the video
device forever without any video actually coming out. Further analysis
showed that it does a VIDIOC_S_FMT with width and height set to -1 (!!!).
The code handling this only cares that both are lower than the minimum
range allowed so it ends up setting the size to 19x17 (!!) This pretty
much breaks the encoder here. Even if this breakage is yet another (TM)
result of my setup, setting the size to 19x17 by default would surprise
most users IMHO.
So, special case for -1 and interpret this to be a request for the
default size, please. Users can then set their favorite size both
through mplayer and through sysfs.
With this patch, mplayer finally works in pvr:// mode (not that we
really gain anything over operating it through sysfs with lirc,
sometime I might actually get off my lazy a** and contribute this
setup too)
Signed-off-by: Pantelis Koukousoulas <pakt223@freemail.gr>
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This should allow mplayer pvr:// to start. The trick is that no matter
what actual input we use under this "fake" one, it will be able to do
stereo :-)
Signed-off-by: Pantelis Koukousoulas <pakt223@freemail.gr>
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Audio mode changes are not private to the audio chip - other I2C
modules need to see this as well. And since the command in question
is VIDIOC_S_TUNER which is a standard v4l2 command, we really should
be broadcasting it out. This change sets up a broadcast pathway for
VIDIOC_S_TUNER and also eliminates the now redundant code from the
audio chip handler.
This fix enables stereo reception for the FM radio
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com>
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Attempts to enumerate or operate on a group of EXT_CTRLS where the
group size is zero is OK; don't fail on such operations. At least one
application uses this to probe for the existence of this API so let it
succeed.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This bug caused uninitalized data to be returned during a G_TUNER status poll.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The lack of a break statement in the handling of VIDIOC_S_TUNER caused
errors to result. Fixed.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rather than hardcoding frequency ranges everywhere, rely on
VIDIOC_G_TUNER results wherever we can.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The automodeswitch control was a feature that enable automatic radio /
tv switching based on the selected frequency. However since frequency
ranges can overlap and also since apparently in some cases it's
possible for the same frequency range to be both tv and radio in a
specific region, then this feature can't safely work. So it's removed.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Clean up use of VIDIOC_G_TUNER; we now correctly gather info from all
the I2C client modules. Also abide by V4L2_TUNER_CAP_LOW
appropriately.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Adds the missing VIDIOC_CROPCAP, G_CROP and S_CROP ioctls, permitting
applications to capture or overlay a subsection of the picture or to
extend the capture window beyond active video, into the VBI area and the
horizontal blanking. VBI capturing can start and end on any line,
including the picture area, and apps can capture different lines of each
field and single fields.
For compatibility with existing applications, the open() function
resets the cropping and VBI capturing parameters and a VIDIOC_S_CROP
call is necessary to actually enable cropping.
Regrettably in PAL-M, PAL-N, PAL-Nc and NTSC-JP mode the maximum image
width will increase from 640 and 768 to 747 and 923 pixels respectively.
Like the VBI changes however, this should only affect applications which
depend on former driver limitations, such as never getting more than 640
pixels regardless of the requested width.
Also, new freedoms require additional checks for conflicts and some
applications may not expect an EBUSY error from the VIDIOC_QBUF and
VIDIOCMCAPTURE ioctls. These errors should be rare though.
So far, the patch has been tested on a UP machine with a bt878 in PAL-
BGHI and NTSC-M mode using xawtv, tvtime, mplayer/mencoder, zapping/
libzvbi and these tools: http://zapping.sf.net/bttv-crop-test.tar.bz2
I'd be grateful about comments or bug reports.
Signed-off-by: Michael H. Schimek <mschimek@gmx.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If assigned minor is 10 or greater, terminator will be put beyound the end.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Switch back to the previous input selection when the radio device is
closed - but only do that if the current input selection is still the
radio (i.e. it appears that it hasn't been messed with).
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When the input is switched by opening /dev/radioX, we must also commit
that change into the driver core.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Clean up and tighten logic involving stream configuration. This
mainly involves changes to pvrusb2-v4l2.c, where we better clarify how
we use the stream configuration enum and implement a cleaner means to
control streaming for a given device node.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The default volume of 65535 is too high. Make is something smaller.
Note that this _only_ changes the default value. Specifically, there
are no scaling or other more intrusive changes here. I'm just sick of
constantly having to reduce the volume every time I plug in and test
the device! (And unfortunately we can't do a better fix like scaling
the volume so that 65535 makes sense because doing so will screw up
any app - like MythTV - which expects the old scaling.) Too bad V4L
controls don't have better defined ranges.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Trying to temporarily check that the stream is not claimed during open
of the radio device is at best a race condition. What's to stop
another app from claiming the stream anyway the instant after the
check is done? The implementation for this was dicey anyway. So it's
removed. The only "price" for this is that if /dev/radioX is opened
while streaming video, then the video stream is just going to switch
to radio mode anyway. If a user does this, he gets what he expects...
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Separate track radio versus tv frequency so that when we switch modes
we can also switch to a sane frequency appropriate for the mode. Also
implement logic to automate mode switching in certain cases.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Implement new method for doing integer range checking, so that we can
more intelligently range-check radio and tv ranges at once.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
These changes implement correct audio routing for radio mode on a
24xxx device.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Report and set correctly converted frequency to/from a V4L2 app.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Frequency units in V4L2 are apparently different when in radio mode
compared to tv mode. Why? Who knows. This change adapts the driver
appropriately - so that internally we always only deal in Hz and don't
have to muck with craziness like this.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A conversion from Hz to V4L frequency units was accidentally removed
by an earlier change. Restore it.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
We can't allocate v4l device structures in a block, since the v4l core
governs when each device actually gets freed. This bug was introduced
as part of the core radio implementation. Fix it.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Support specification of vbi and radio device minor numbers in a
manner similar to the video device minor number.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Ensure we don't accidentally broadcast the standard while in radio mode.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The initial radio implementation used different units for tuning when
in radio mode. This changes everything to Hz.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
