The dm9000 driver expects two IORESOURCE_MEM to get at the device, so make
sure we declare things properly.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Latest smc91x driver allows you to specify settings in board resources
rather than needing CONFIG_BLACKFIN in the drivers/net/smc91x.h header.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The interrupt probe workaround doesn't work without hacks to common code,
and the add-on card only needs a simple resistor to fix the problem, so
drop the board-specific hack.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Since the hardware only provides reporting for the last exception handled,
and the values are valid only when executing the exception handler, we
need to save the context for reporting at a later point. While we do this
for one exception, it doesn't work properly when handling a second one as
the original exception is clobbered by the double fault. So when double
fault debugging is enabled, create a dedicated shadow of these values and
save/restore out of there. Now the crash report properly displays the
first exception as well as the second one.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
One too many zeros means we run way faster than the codec can handle.
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The protect_page() function was incorrectly setting up the hardware tables
based on possible access capabilities rather than the actual requested
values. This means we would grant more access to mmap-ed pages than we
should have. Once we fix this, we need to tweak the signal generated by
such accesses to aline ourselves with other ports. This allows the LTP
mmap0{5,6,7} cases to run properly.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
I2C_BOARD_INFO() already sets .type, no need to set it again.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Push the device table to the board resources as data interpretation can be
changed on a per-board basis.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The end of the stack may not be valid (and that could be OK), so do not
attempt to parse it. If we do, we might use a bad pointer in kernel space
which makes things panic().
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Add the bf538 version of bfin_clear_PPI_STATUS() to match all other ports.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The initial BF54x port included some defines to keep code simple across
different processors, but it just ended up causing the UART0 DMA IRQs to
be set to the UART1 channels.
Signed-off-by: Stefan Pledl <stefan.pledl@mesutronic.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Allow hardware errors to be caught during early portions of booting, and
leave something in the shadow console that people can use to debug their
system with (to be printed out by the bootloader on next reset).
This enables the hardare error interrupts in head.S, allowing us to find
hardware errors when they happen (well, as much as you can with a hardware
error) and prints out the trace if it is enabled. This will catch errors
(like booting the wrong image on a 533) which previously resulted in a
infinite loop/hang, as well as random hardware errors before before
setup_arch().
To disable this debug only feature - turn off EARLY_PRINTK.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Add a memory based shadow console to keep a copy of the printk buffer in a
location which can be found externally. This allows bootloaders to locate
and utilize the log buffer in case of silent (early/resume/etc...) crashes.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The FDPIC arches support a standard set of ptrace requests so rather than
define our own custom API, hook up those requests for common code to
leverage.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Rather than defining the locks and initializing them all the time, only do
so when we actually need them (i.e. the SRAM regions exist). This avoids
dead data and code bloat during runtime.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The "TWI_KEYPAD" driver was renamed to "INPUT_PCF8574", so update the
defines in the board resources accordingly.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Remove code duplication, and only print out memory warnings when they are
an actual problem.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The current module relocation code has spotty handling wrt different
memory regions (like L1 instruction). Rather than try to fix each
little spot, use the new common memory functions to greatly simplify
everything and make sure it is always correct.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The current module section handling code has a lot of verbose statements
copied and pasted throughout which makes it pretty hard to digest at a
glance. By unifying all of these up front, it is a lot easier to quickly
get an idea of what is actually going on.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Convert all printk() statements to use the common pr_xxx() funcs and use
the new pr_fmt() function to standardize all of the output.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
All kernel modules are required to be built with -mlong-calls and thus
should not generate any of these relocations. If they do, it means the
module has not been compiled properly, so rather than trying to handle
them (and running into random run time errors) just error out on module
load to force the module to be compiled correctly.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Now that we have a Blackfin memory function to figure out how to properly
access the different regions, drop the custom memory range checks in our
ptrace code and use that. It makes the code nicer and fixes bugs where
the ptrace logic wasn't handling all the different regions.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Unify the address display to shrink the code, and add missing decoding of
a few special Blackfin-specific regions (L1 ROM and MMRs).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cleanup is performed in two ways:
- remove extraneous updates of IPEND[4] w/ CONFIG_IPIPE,
and document remaining use.
- substitute pop-reg-from-stack instructions with plain SP fixups in
all save-RETI-then-discard patterns.
Signed-off-by: Philippe Gerum <rpm@xenomai.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The purpose of the EVT14 handler may depend on whether CONFIG_IPIPE is
enabled, albeit its implementation can be the same in both cases. When
the interrupt pipeline is enabled, EVT14 can be used to raise the core
priority level for the running code; when CONFIG_IPIPE is off, EVT14
can be used to lower this level before running softirq handlers.
Rename evt14_softirq to evt_evt14 to pick an identifier that fits
both, which allows to reuse the same vector setup code as well.
Signed-off-by: Philippe Gerum <rpm@xenomai.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
ret_from_fork is always entered with hw interrupts off, which prevents
real-time domains to preempt the Linux kernel during part of the
initial context switch to the new task, which could in turn raise the
worst-case latency figures.
To avoid this, stall the root domain stage in the interrupt pipeline
to keep the scheduling tail code free from Linux-handled IRQs, then
enable hardware interrupts again.
Signed-off-by: Philippe Gerum <rpm@xenomai.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
__ipipe_{stall, unstall}_root_raw() identifiers may leave the reader
under the impression that only the virtual state is affected by these
operations, which is wrong. Pick names following the convention used
throughout the interrupt pipeline code.
Signed-off-by: Philippe Gerum <rpm@xenomai.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We handle many exceptions at EVT5 (hardware error level) so that we can
catch exceptions in our exception handling code. Today - if the global
interrupt enable bit (IPEND[4]) is set (interrupts disabled) our trap
handling code goes into a infinite loop, since we need interrupts to be
on to defer things to EVT5.
Normal kernel code should not trigger this for any reason as IPEND[4] gets
cleared early (when doing an interrupt context save) and the kernel stack
there should be sane (or something much worse is happening in the system).
But there have been a few times where this has happened, so this change
makes sure we dump a proper crash message even when things have gone south.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
Driver Core: devtmpfs - kernel-maintained tmpfs-based /dev
debugfs: Modify default debugfs directory for debugging pktcdvd.
debugfs: Modified default dir of debugfs for debugging UHCI.
debugfs: Change debugfs directory of IWMC3200
debugfs: Change debuhgfs directory of trace-events-sample.h
debugfs: Fix mount directory of debugfs by default in events.txt
hpilo: add poll f_op
hpilo: add interrupt handler
hpilo: staging for interrupt handling
driver core: platform_device_add_data(): use kmemdup()
Driver core: Add support for compatibility classes
uio: add generic driver for PCI 2.3 devices
driver-core: move dma-coherent.c from kernel to driver/base
mem_class: fix bug
mem_class: use minor as index instead of searching the array
driver model: constify attribute groups
UIO: remove 'default n' from Kconfig
Driver core: Add accessor for device platform data
Driver core: move dev_get/set_drvdata to drivers/base/dd.c
Driver core: add new device to bus's list before probing
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/pcmcia-2.6:
pcmcia: document return value of pcmcia_loop_config
pcmcia: dtl1_cs: fix pcmcia_loop_config logic
pcmcia: drop non-existant includes
pcmcia: disable prefetch/burst for OZ6933
pcmcia: fix incorrect argument order to list_add_tail()
pcmcia: drivers/pcmcia/pcmcia_resource.c: Remove unnecessary semicolons
pcmcia: Use phys_addr_t for physical addresses
pcmcia: drivers/pcmcia: Make static
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (75 commits)
PCI hotplug: clean up acpi_run_hpp()
PCI hotplug: acpiphp: use generic pci_configure_slot()
PCI hotplug: shpchp: use generic pci_configure_slot()
PCI hotplug: pciehp: use generic pci_configure_slot()
PCI hotplug: add pci_configure_slot()
PCI hotplug: clean up acpi_get_hp_params_from_firmware() interface
PCI hotplug: acpiphp: don't cache hotplug_params in acpiphp_bridge
PCI hotplug: acpiphp: remove superfluous _HPP/_HPX evaluation
PCI: Clear saved_state after the state has been restored
PCI PM: Return error codes from pci_pm_resume()
PCI: use dev_printk in quirk messages
PCI / PCIe portdrv: Fix pcie_portdrv_slot_reset()
PCI Hotplug: convert acpi_pci_detect_ejectable() to take an acpi_handle
PCI Hotplug: acpiphp: find bridges the easy way
PCI: pcie portdrv: remove unused variable
PCI / ACPI PM: Propagate wake-up enable for devices w/o ACPI support
ACPI PM: Replace wakeup.prepared with reference counter
PCI PM: Introduce device flag wakeup_prepared
PCI / ACPI PM: Rework some debug messages
PCI PM: Simplify PCI wake-up code
...
Fixed up conflict in arch/powerpc/kernel/pci_64.c due to OF device tree
scanning having been moved and merged for the 32- and 64-bit cases. The
'needs_freset' initialization added in 6e19314cc ("PCI/powerpc: support
PCIe fundamental reset") is now in arch/powerpc/kernel/pci_of_scan.c.
* 'writeback' of git://git.kernel.dk/linux-2.6-block:
writeback: fix possible bdi writeback refcounting problem
writeback: Fix bdi use after free in wb_work_complete()
writeback: improve scalability of bdi writeback work queues
writeback: remove smp_mb(), it's not needed with list_add_tail_rcu()
writeback: use schedule_timeout_interruptible()
writeback: add comments to bdi_work structure
writeback: splice dirty inode entries to default bdi on bdi_destroy()
writeback: separate starting of sync vs opportunistic writeback
writeback: inline allocation failure handling in bdi_alloc_queue_work()
writeback: use RCU to protect bdi_list
writeback: only use bdi_writeback_all() for WB_SYNC_NONE writeout
fs: Assign bdi in super_block
writeback: make wb_writeback() take an argument structure
writeback: merely wakeup flusher thread if work allocation fails for WB_SYNC_NONE
writeback: get rid of wbc->for_writepages
fs: remove bdev->bd_inode_backing_dev_info
wb_clear_pending AFAIKS should not be called after the item has been
put on the list, except by the worker threads. It could lead to the
situation where the refcount is decremented below 0 and cause lots of
problems.
Presumably the !wb_has_dirty_io case is not a common one, so it can
be discovered when the thread wakes up to check?
Also add a comment in bdi_work_clear.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
By the time bdi_work_on_stack gets evaluated again in bdi_work_free, it
can already have been deallocated and used for something else in the
!on stack case, giving a false positive in this test and causing
corruption.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
If you're going to do an atomic RMW on each list entry, there's not much
point in all the RCU complexities of the list walking. This is only going
to help the multi-thread case I guess, but it doesn't hurt to do now.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>