Many features of h3100/h3600 (LCD, PCMCIA, Flash write, etc.)
depend on correct functioning of GPIO expander handled by htc-egpio
driver, so force its building in Kconfig.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update defconfig to current kernel, enable support for iPAQ H3100
and following drivers: gpio-keys, htc-egpio, ide_cs.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Both iPAQs h3600 and h3100 share the same control
GPIOs for PCMCIA, so driver can be reused.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for "Power" and "Action" (joystick center) buttons -
the only buttons on iPaq h3100/h3600 connected to GPIOs
(other buttons are controlled by microcontroller)
Also remove setting PWER for wakeup on Power button press -
gpio-keys driver will handle it.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
After a code reorganization and following split, there's some #includes
now unused. Clean them up and sort remaining alphabetticaly where possible.
Compile tested.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Correct boilerplates after files split. Also shorten them a bit - use
standart GPL wording (as per http://lkml.org/lkml/2007/5/1/220) and
drop changelog, which only entry about h3800 support and abstracted
EGPIOs is just confusing now, as both of these features are gone.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Split common h3600.c into three separate files: h3100.c, h3600.c and
h3xxx.c (the latter contains common code for h3100/h3600)
Copyright boilerplates and #includes are copied intact and will be
cleaned up later.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Combine both headers into one, rename to h3xxx.h and change all
users accordingly.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As all existing code was converted to gpiolib, drop no more
used pre-gpiolib (bit-shifted) GPIO definintions.
Supply new gpiolib-friendly definitions for GPIOs which
don't have them yet.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
After conversion to gpiolib there's still some GPIOs left, that get
configured in *_mach_init() as outputs (using direct operations
on GPCR/GPDR registers), but otherwise unused. These GPIOs are mainly
sound related and should be configured by corresponding driver once
it is written.
Drop this initialisation and configure all GPIOs as input.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As all the remaining users of these definitions
(in pcmcia/sa1100_h3600 driver) were converted to gpio_to_irq(),
they can be safely removed.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As all users of assign_h3600_egpio now converted to gpiolib, we
can safely remove all assign_h3600_egpio handling code and
definitions.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use of gpio_request/gpio_free in some callbacks may look ugly, but
corresponding drivers (sa1100_serial and sa1100_fb) don't provide (yet)
init/exit hooks and registering these gpios in *_mach_init is also
not possible, because htc-gpio driver starts a bit later...
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It will be used for future conversion of assign_h3600_egpio calls to
gpiolib.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
h3100 and h3600 have different sets of LCD-controlling gpios,
which mapped to the same "abstracted" EGPIO.
As we plan to get rid of those abstracted egpios completely, we
need to separate these helper functions.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert all operations with GPLR/GPCR/GPSR to gpiolibs calls.
Also change all IRQ_GPIO* to gpio_to_irq(*GPIO*)
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
PM_SUSPEND, PM_RESUME and machine_is_h3xxx() are not used anywhere in
kernel (checked with git grep), so it's safe to remove them.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
IRDA is handled by separate sa1100-ir driver and has
nothing to do with sa1100_serial
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
No point calling sa1100_register_uart_fns early - these aren't
used until late in the boot sequence. Also convert to gpiolib
support.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'x86-debug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Limit number of per cpu TSC sync messages
x86: dumpstack, 64-bit: Disable preemption when walking the IRQ/exception stacks
x86: dumpstack: Clean up the x86_stack_ids[][] initalization and other details
x86, cpu: mv display_cacheinfo -> cpu_detect_cache_sizes
x86: Suppress stack overrun message for init_task
x86: Fix cpu_devs[] initialization in early_cpu_init()
x86: Remove CPU cache size output for non-Intel too
x86: Minimise printk spew from per-vendor init code
x86: Remove the CPU cache size printk's
cpumask: Avoid cpumask_t in arch/x86/kernel/apic/nmi.c
x86: Make sure we also print a Code: line for show_regs()
* 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, msr, cpumask: Use struct cpumask rather than the deprecated cpumask_t
x86, cpuid: Simplify the code in cpuid_open
x86, cpuid: Remove the bkl from cpuid_open()
x86, msr: Remove the bkl from msr_open()
x86: AMD Geode LX optimizations
x86, msr: Unify rdmsr_on_cpus/wrmsr_on_cpus
* 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Fix a section mismatch in arch/x86/kernel/setup.c
x86: Fixup last users of irq_chip->typename
x86: Remove BKL from apm_32
x86: Remove BKL from microcode
x86: use kernel_stack_pointer() in kprobes.c
x86: use kernel_stack_pointer() in kgdb.c
x86: use kernel_stack_pointer() in dumpstack.c
x86: use kernel_stack_pointer() in process_32.c
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
include/linux/compiler-gcc4.h: Fix build bug - gcc-4.0.2 doesn't understand __builtin_object_size
x86/alternatives: No need for alternatives-asm.h to re-invent stuff already in asm.h
x86/alternatives: Check replacementlen <= instrlen at build time
x86, 64-bit: Set data segments to null after switching to 64-bit mode
x86: Clean up the loadsegment() macro
x86: Optimize loadsegment()
x86: Add missing might_fault() checks to copy_{to,from}_user()
x86-64: __copy_from_user_inatomic() adjustments
x86: Remove unused thread_return label from switch_to()
x86, 64-bit: Fix bstep_iret jump
x86: Don't use the strict copy checks when branch profiling is in use
x86, 64-bit: Move K8 B step iret fixup to fault entry asm
x86: Generate cmpxchg build failures
x86: Add a Kconfig option to turn the copy_from_user warnings into errors
x86: Turn the copy_from_user check into an (optional) compile time warning
x86: Use __builtin_memset and __builtin_memcpy for memset/memcpy
x86: Use __builtin_object_size() to validate the buffer size for copy_from_user()
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (30 commits)
x86, apic: Enable lapic nmi watchdog on AMD Family 11h
x86: Remove unnecessary mdelay() from cpu_disable_common()
x86, ioapic: Document another case when level irq is seen as an edge
x86, ioapic: Fix the EOI register detection mechanism
x86, io-apic: Move the effort of clearing remoteIRR explicitly before migrating the irq
x86: SGI UV: Map low MMR ranges
x86: apic: Print out SRAT table APIC id in hex
x86: Re-get cfg_new in case reuse/move irq_desc
x86: apic: Remove not needed #ifdef
x86: io-apic: IO-APIC MMIO should not fail on resource insertion
x86: Remove asm/apicnum.h
x86: apic: Do not use stacked physid_mask_t
x86, apic: Get rid of apicid_to_cpu_present assign on 64-bit
x86, ioapic: Use snrpintf while set names for IO-APIC resourses
x86, apic: Use PAGE_SIZE instead of numbers
x86: Remove local_irq_enable()/local_irq_disable() in fixup_irqs()
x86: Use EOI register in io-apic on intel platforms
x86: Force irq complete move during cpu offline
x86: Remove move_cleanup_count from irq_cfg
x86, intr-remap: Avoid irq_chip mask/unmask in fixup_irqs() for intr-remapping
...
* 'tracing-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (40 commits)
tracing: Separate raw syscall from syscall tracer
ring-buffer-benchmark: Add parameters to set produce/consumer priorities
tracing, function tracer: Clean up strstrip() usage
ring-buffer benchmark: Run producer/consumer threads at nice +19
tracing: Remove the stale include/trace/power.h
tracing: Only print objcopy version warning once from recordmcount
tracing: Prevent build warning: 'ftrace_graph_buf' defined but not used
ring-buffer: Move access to commit_page up into function used
tracing: do not disable interrupts for trace_clock_local
ring-buffer: Add multiple iterations between benchmark timestamps
kprobes: Sanitize struct kretprobe_instance allocations
tracing: Fix to use __always_unused attribute
compiler: Introduce __always_unused
tracing: Exit with error if a weak function is used in recordmcount.pl
tracing: Move conditional into update_funcs() in recordmcount.pl
tracing: Add regex for weak functions in recordmcount.pl
tracing: Move mcount section search to front of loop in recordmcount.pl
tracing: Fix objcopy revision check in recordmcount.pl
tracing: Check absolute path of input file in recordmcount.pl
tracing: Correct the check for number of arguments in recordmcount.pl
...
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
tracing: Fix trace_marker output
tracing: Fix event format export
tracing: Fix return value of tracing_stats_read()
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (31 commits)
rcu: Make RCU's CPU-stall detector be default
rcu: Add expedited grace-period support for preemptible RCU
rcu: Enable fourth level of TREE_RCU hierarchy
rcu: Rename "quiet" functions
rcu: Re-arrange code to reduce #ifdef pain
rcu: Eliminate unneeded function wrapping
rcu: Fix grace-period-stall bug on large systems with CPU hotplug
rcu: Eliminate __rcu_pending() false positives
rcu: Further cleanups of use of lastcomp
rcu: Simplify association of forced quiescent states with grace periods
rcu: Accelerate callback processing on CPUs not detecting GP end
rcu: Mark init-time-only rcu_bootup_announce() as __init
rcu: Simplify association of quiescent states with grace periods
rcu: Rename dynticks_completed to completed_fqs
rcu: Enable synchronize_sched_expedited() fastpath
rcu: Remove inline from forward-referenced functions
rcu: Fix note_new_gpnum() uses of ->gpnum
rcu: Fix synchronization for rcu_process_gp_end() uses of ->completed counter
rcu: Prepare for synchronization fixes: clean up for non-NO_HZ handling of ->completed counter
rcu: Cleanup: balance rcu_irq_enter()/rcu_irq_exit() calls
...
* 'core-printk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
ratelimit: Make suppressed output messages more useful
printk: Remove ratelimit.h from kernel.h
ratelimit: Fix/allow use in atomic contexts
ratelimit: Use per ratelimit context locking
* 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
mutex: Fix missing conditions to build mutex_spin_on_owner()
mutex: Better control mutex adaptive spinning config
locking, task_struct: Reduce size on TRACE_IRQFLAGS and 64bit
locking: Use __[SPIN|RW]_LOCK_UNLOCKED in [spin|rw]_lock_init()
locking: Remove unused prototype
locking: Reduce ifdefs in kernel/spinlock.c
locking: Make inlining decision Kconfig based
* 'core-iommu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (63 commits)
x86, Calgary IOMMU quirk: Find nearest matching Calgary while walking up the PCI tree
x86/amd-iommu: Remove amd_iommu_pd_table
x86/amd-iommu: Move reset_iommu_command_buffer out of locked code
x86/amd-iommu: Cleanup DTE flushing code
x86/amd-iommu: Introduce iommu_flush_device() function
x86/amd-iommu: Cleanup attach/detach_device code
x86/amd-iommu: Keep devices per domain in a list
x86/amd-iommu: Add device bind reference counting
x86/amd-iommu: Use dev->arch->iommu to store iommu related information
x86/amd-iommu: Remove support for domain sharing
x86/amd-iommu: Rearrange dma_ops related functions
x86/amd-iommu: Move some pte allocation functions in the right section
x86/amd-iommu: Remove iommu parameter from dma_ops_domain_alloc
x86/amd-iommu: Use get_device_id and check_device where appropriate
x86/amd-iommu: Move find_protection_domain to helper functions
x86/amd-iommu: Simplify get_device_resources()
x86/amd-iommu: Let domain_for_device handle aliases
x86/amd-iommu: Remove iommu specific handling from dma_ops path
x86/amd-iommu: Remove iommu parameter from __(un)map_single
x86/amd-iommu: Make alloc_new_range aware of multiple IOMMUs
...
* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-nmw: (31 commits)
GFS2: Fix glock refcount issues
writeback: remove unused nonblocking and congestion checks (gfs2)
GFS2: drop rindex glock to refresh rindex list
GFS2: Tag all metadata with jid
GFS2: Locking order fix in gfs2_check_blk_state
GFS2: Remove dirent_first() function
GFS2: Display nobarrier option in /proc/mounts
GFS2: add barrier/nobarrier mount options
GFS2: remove division from new statfs code
GFS2: Improve statfs and quota usability
GFS2: Use dquot_send_warning()
VFS: Export dquot_send_warning
GFS2: Add set_xquota support
GFS2: Add get_xquota support
GFS2: Clean up gfs2_adjust_quota() and do_glock()
GFS2: Remove constant argument from qd_get()
GFS2: Remove constant argument from qdsb_get()
GFS2: Add proper error reporting to quota sync via sysfs
GFS2: Add get_xstate quota function
GFS2: Remove obsolete code in quota.c
...
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6: (30 commits)
TOMOYO: Add recursive directory matching operator support.
remove CONFIG_SECURITY_FILE_CAPABILITIES compile option
SELinux: print denials for buggy kernel with unknown perms
Silence the existing API for capability version compatibility check.
LSM: Move security_path_chmod()/security_path_chown() to after mutex_lock().
SELinux: header generation may hit infinite loop
selinux: Fix warnings
security: report the module name to security_module_request
Config option to set a default LSM
sysctl: require CAP_SYS_RAWIO to set mmap_min_addr
tpm: autoload tpm_tis based on system PnP IDs
tpm_tis: TPM_STS_DATA_EXPECT workaround
define convenient securebits masks for prctl users (v2)
tpm: fix header for modular build
tomoyo: improve hash bucket dispersion
tpm add default function definitions
LSM: imbed ima calls in the security hooks
SELinux: add .gitignore files for dynamic classes
security: remove root_plug
SELinux: fix locking issue introduced with c6d3aaa4e3
...
