FTM time sync feature is triggered when connection takes place
in case of STA and bss starts in case of SAP. The feature is
stopped when STA disconnects and bss stops.
Change-Id: I963b0134b7432c9827c2fb3d9dce7c81a8666d4d
CRs-Fixed: 2621144
Add ini config required for FTM time sync feature.
"enable_time_sync_ftm"- ini to enable/disable the feature.
"time_sync_ftm_mode" - ini to configure the burst/aggregated mode.
In burst mode the offset derived for each RTT frame is sent by
firmware, in aggregated mode only one offset is sent by firmware.
"time_sync_ftm_role" - ini to configure slave(STA)/master(SAP) role.
Change-Id: I6a06d6fdc4c7556c32ab2d28f1cbaa936b98a85b
CRs-Fixed: 2618654
Register tx and rx ops to send packet capture mode command and
to receive mgmt offload handler for packet capture component.
Change-Id: I70da00feff29399b98c5916eec17e26b62285db3
CRs-Fixed: 2619321
If resume and fw wakeup happens at the same time.
psoc_ctx->lock maybe doing bottom half operation for resume,
then wakeup interrupt comes on same cpu, the interrupt
handler will also acquire psoc_ctx->lock in
pmo_core_update_wow_initial_wake_up, which cause dead lock.
Using atomic for wow_initial_wake_up, so the interrupt handler
can avoid using spin_lock.
Change-Id: Id0e963a0924415e9660c57a1c1b776d3e609213d
CRs-Fixed: 2624899
Add support for the following NAN messages in kmsg:-
1. NAN enable status
2. NAN, NDP match events
3. NDP channel info.
etc.
Change-Id: Icbf8f4ed05a7bd181a076d526dd2e01d70be6b05
CRs-Fixed: 2618835
Enhance logs in policy mgr module to remove duplicate
or unwanted prints and keep only useful logs to debug.
Change-Id: Ifd585256955aceec29286d82838be0c588228c32
CRs-Fixed: 2614763
Process management Tx and Rx frames for packet capture mode
and post frames to the mon thread.
Change-Id: I14c0a1cf8a8aa4d4a4e16ad6200715b875611c81
CRs-Fixed: 2619317
Send vdev param command to FW for STA vdev to set the packet
capture mode. Send the command only if packet capture support
is enabled.
Change-Id: Ifed2431882b1f7d2869771e812daa5bcd5dc17e9
CRs-Fixed: 2619314
During CU and low rssi based roam triggers, consider AP as roam candidate
only if its roam score is better than connected AP score by at least
min_roam_score_delta.
User configures this candidate minimum roam score delta value using
"min_roam_score_delta" INI. User can set candidate minimum score delta
value between 0 to 10000 and default value is 1850.
Firmware will trigger roaming only if roam score of candidate AP is
greater than "min_roam_score_delta" & "roam_score_delta" values of
connected AP.
Change-Id: I180e769b5629aa405dbd89ed73e39e228adf92db
CRS-Fixed: 2614117
Add the function to parse the FTM timesync start/stop and offset
events received from target and populate them in ftm timsync
priv vdev structure.
Change-Id: Ibdcf97bb0a04fc6490c6bd2c26701036df92c5d4
CRs-Fixed: 2618646
Currently, host driver sends disconnect reason code as UNSPECIFIED
to kernel in most of the disconnection scenarios. Correct the same
to send proper reason code received from peer in case of peer
initiated disconnections.
Introduce new reason codes for internal disconnections and assign
proper reason code for each possible disconnect scenario.
Change-Id: I99bf4573b59dc810e0a1529fcd48061d10acae4e
CRs-Fixed: 2622310
Scan cmd still can be exist after scheduler thread is suspended
when host suspend, the scan cmd can't be removed from
serialization list by either complete or cancel any more since
both depends on scheduler thread, suspend thread blocked 30s to
wait scan cmd cleared.
Roam sync event from F/W can't be handled and Roam sync complete
can't be sent to F/W since scheduler thread suspended, then F/W
assert for roam sync cmd timeout.
After receive F/W down event, host will try SSR, but blocked by
unfinished suspend thread too.
Fix: suspend all components including scan before suspend
scheduler thread, make sure scan cmd is cleared and no new scan
is allowed any more before scheduler thread suspended.
Change-Id: I7a3badeedea018e4d92bbe8660692e42923852aa
CRs-Fixed: 2620650
Move disconnect ie info to a structure (wlan_disconnect_info)
and use it in mlme_legacy_priv. This helps to enhance the
structure further.
Change-Id: Id16e7eeb45a3f4c2fefac297f6730baf6b9e8991
CRs-Fixed: 2621149
Currently, when WWAN channel changes, the list of WLAN channels that
needs to be avoided is given to WLAN FW. WLAN FW indicates the list
to host. Upon receiving Channel avoidance indication, host switches
the operating-channel of SAP (if any and conflicting).
When there is a frequent channel change from WWAN side, it causes
frequent SAP disconnection. To mitigate this problem, as part of
this change send the configuration to the WLAN FW which delays
the channel avoidance indication before sending it to host.
Change-Id: If67775d59b9f61d3592a5f6609d3b002899e5daf
CRs-Fixed: 2615917
Optimize logs while sending assoc req and assoc rsp handling
frame by dumping the assoc req frame and not printing each
params separately. Also avoid multiple dump of same frame.
Change-Id: Ibcf2d9aa8de292b9b9f4b4c6a53a0f694d69475c
CRs-Fixed: 2619553
Currently there are lot of duplicate logging. Identify and
reduce those logs that are not absolutely necessary.
Change-Id: Ia2df5a46610b885be5e27455aef7f7281c7c3c55
CRs-Fixed: 2617719
Add INI parameter for packet capture mode
"packet_capture_mode" - ini to set packet capture mode.
Change-Id: Ie60c142af753c65b44aa0018440e43a215e51a27
CRs-Fixed: 2614578
idle_roam_rssi_delta - This threshold is the criteria to decide whether
DUT is idle or moving. If rssi delta is more than configured thresold
then its considered as not idle. RSSI delta is entered in dBm. Idle
roaming can be triggered if the connected AP rssi change exceeds or
falls below the rssi delta and if other criteria of ini
"enable_idle_roam" is met.
To enhance idle roaming, idle_roam_rssi_delta default value is changed
to 3.
Change-Id: I9a5b06081d59d8502c40df0485c2b997cbcb2b80
CRs-Fixed: 2619436
AP has less keep alive timer than STA, so AP is kicking out the STA and
sending the deauth.
To resolve this change CFG_INFRA_STA_KEEP_ALIVE_PERIOD_DEFAULT value from
60 to 30.
Change-Id: I0522071bc634b029178de6e09c11d237351a334d
CRs-Fixed: 2616279
When application issues NDP end to terminate an NDP connection,
host driver sends a request to the firmware and firmware
terminates the NDP by sending NDP end frame to the peer.
Currently, driver returns immediately after posting request to
the firmware. Application might issue NDI delete immediately
after returning from NDP_END request.
But firmware might take some time to complete the NDP termination
and send NDP_END indication to driver.
When driver tries to delete the NDI before receiving NDP_END
indication from firmware, it causes inconsistency in firmware as
the NDI on which the NDP is parked is freed.
So, wait till the NDP_END indication comes from
firmware(or timeout happens) before returning from ndp_end request
context.
Change-Id: Ied7ed36451ef007e38f67d48c54290b9dd674f54
CRs-Fixed: 2616018
Currently there is no inis for NAN component:
1. To configure the keep alive period for the
NDI interface.
2. To enable/disable discovery of NAN cluster with
Master Preference (MP) as 0 when a new device is
enabling NAN.
Add ini support to configure above mentioned values.
Change-Id: I47b67eb89fb8849960a9f492d2909e45b96308f3
CRs-Fixed: 2617839
This patchset adds the FTM TIME SYNC component in
target_if to register the ftm time sync wmi events/cmds.
Change-Id: I4ea14266a912c9d261a67809556774860b5ddab1
CRs-Fixed: 2617055
Currently there are lot of duplicate logging. Identify and
reduce those logs that are not absolutely necessary.
Change-Id: I649ce3bec8c3c8542fe9edd08907da9ab01fa948
CRs-Fixed: 2617504
Add support to customize DSCP-to-UP map table and send the
customized map values to FW to update its corresponding
map table.
Change-Id: Ibe9704a90468c898dd2e60fdf83a271152f654ce
CRs-Fixed: 2616247
In case of successful wow enable ack from FW for system
suspend call cdp wow ack response process, so that dp
layer will take care of required operations before system
goes to suspend.
Change-Id: Ibc5bf8d62aa055c9c8c7242c00abc3b696bb0051
CRs-Fixed: 2608980
As part of new requirement WLAN subsystem needs to perform thermal
mitigation action as per the thermal state of the device. The
wifi hal sends vendor command QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD
with the thermal level parameter and wlan host performs the required
appropriate action. wlan host driver maps the thermal level to
corresponding duty cycle off percent value and duty cycle value,
send WMI_THERM_THROT_SET_CONF_CMDID cmd to FW.
Make changes to perform vendor command handling, mapping thermal level
to duty cycle value and communicating the thermal information to FW.
change-ID: I77175048c817ab755cdb838018e414ef3ee0b112
CRs-Fixed: 2610395
Add a new INI parameter "nan_separate_iface_support" to
indicate firmware that the host driver supports separate
interface for NAN Discovery.
Change-Id: I6fb313b02c5f3a05638e85494051fb003b2dd867
CRs-Fixed: 2612006
In FTM mode, no peer is created in the host. Currently, since
peer_unmap_conf_support feature is enabled, FW is expecting
WMA_SEND_PEER_UNMAP_CONF from host to remove the peer Id from AST.
But host never send this WMI CMD in FTM mode.
Disable peer_unmap_conf_support in FTM mode which allow FW to
delete the peer Id without any WMI CMD expectation from host.
Change-Id: Idf9082adc81187346563f3aedf1f1657164f03cc
CRs-Fixed: 2608929
arp_ns_offload and gtk offload command are being issued for NaN mode
vdev. NaN mode vdev does not support ARP_NS and GTK off load features,
so disable them when in NaN mode.
Change-Id: Iab11c92bb5da4004b62e642342a386f532832509
CRs-Fixed: 2608618
Add support to make event WMI_ROAM_PMKID_REQUEST_EVENTID as
wakable in FIPS case.
In FIPS Enabled case, for roaming Firmware sends PMKID request
to host as firmware is not supposed to do crypto functionality
with FIPS enabled.
Change-Id: I09b6b68f77ba75f9e5519ff18017c95d16771f52
CRs-Fixed: 2513790
STA considers RSSI delta configured by the user along with other
parameters for roaming.
RoamRssiDiff is the number of units (typically measured in dB) AP2 is
better than AP1. STA roams from connected AP1 to AP2 if the RSSI value
of AP2 is greater than AP1 by configured ROAM delta value.
Max limit of RoamRssiDiff is increased to 100 from 30, so user can set
roam delta from 0 to 100 using command SETROAMDELTA.
Change-Id: I69b783ebe5ec971bb62cbac8a34065d52fc25422
CRs-Fixed: 2609589
Update the mlme_get_roam_fail_reason_str() to return
correct string for new roam failure reason enums added.
Change-Id: I24983149fdcd8a0935eea9670832944638c33179
CRs-Fixed: 2607545
