ioremap must be balanced by an iounmap and failing to do so can result
in a memory leak.
Signed-off-by: Amol Lad <amol@verismonetworks.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@osdl.org>
This is patch 16 in the series of patches that converts
Marcus Junker's w83697hf watchdog driver to Samuel Tardieau's
w83697hf/hg watchdog driver.
This patch contains following changes:
- Add copyright notice for Samuel Tardieu also.
This is the last patch in this series.
The original description for Samuel's driver was:
driver for the Winbond W83697HF/W83697HG watchdog timer
The Winbond SuperIO W83697HF/HG includes a watchdog that can count from
1 to 255 seconds (or minutes). This drivers allows the seconds mode to
be used. It exposes a standard /dev/watchdog interface. This chip is
currently being used on some motherboards designed by VIA.
By default, the module looks for a chip at I/O port 0x2e. The chip can
be configured to be at 0x4e on some motherboards, the address can be
chosen using the wdt_io module parameter. Using 0 will try to autodetect
the address.
Signed-off-by: Samuel Tardieu <sam@rfc1149.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This is patch 15 in the series of patches that converts
Marcus Junker's w83697hf watchdog driver to Samuel Tardieau's
w83697hf/hg watchdog driver.
This patch contains following changes:
- Clean-up initialization code - part 2:
* the line reading "set second mode & disable keyboard ..."
is plain wrong, the register being manipulated (CRF4) is
the counter itself, not the control byte (CRF3) -- looks
like it has been copied from another driver.
* I think garbage is being written in CRF3 (the control word)
as the timeout value is being stored in this register (such
as 60 for 60 seconds).
* We only want to set pin 119 to WDTO# mode and leave the rest
of CR29 like it is.
* Set count mode to seconds and not minutes.
Signed-off-by: Samuel Tardieu <sam@rfc1149.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This is patch 14 in the series of patches that converts
Marcus Junker's w83697hf watchdog driver to Samuel Tardieau's
w83697hf/hg watchdog driver.
This patch contains following changes:
- Clean-up initialization code (part 1: remove
w83697hf_select_wd_register() and
w83697hf_unselect_wd_register() functions).
- Make sure that the watchdog device is stopped
as soon as we found it.
Signed-off-by: Samuel Tardieu <sam@rfc1149.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This is patch 13 in the series of patches that converts
Marcus Junker's w83697hf watchdog driver to Samuel Tardieau's
w83697hf/hg watchdog driver.
This patch contains following changes:
- Remove wdt_ctrl (it has been replaced with the
w83697hf_write_timeout() function) and redo/clean-up
the start/stop/ping code.
- Make sure that the watchdog is enabled or disabled
When starting or stoping the device (with a call
to w83697hf_set_reg(0x30, ?); ).
Signed-off-by: Samuel Tardieu <sam@rfc1149.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This is patch 12 in the series of patches that converts
Marcus Junker's w83697hf watchdog driver to Samuel Tardieau's
w83697hf/hg watchdog driver.
This patch contains following changes:
- Add w83697hf_write_timeout() to set the
watchdog's timeout value.
Signed-off-by: Samuel Tardieu <sam@rfc1149.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This is patch 11 in the series of patches that converts
Marcus Junker's w83697hf watchdog driver to Samuel Tardieau's
w83697hf/hg watchdog driver.
This patch contains following changes:
- Add w83697hf_select_wdt() and w83697hf_deselect_wdt()
so that the start/stop/ping code can directly talk to
the watchdog.
Signed-off-by: Samuel Tardieu <sam@rfc1149.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This is patch 10 in the series of patches that converts
Marcus Junker's w83697hf watchdog driver to Samuel Tardieau's
w83697hf/hg watchdog driver.
This patch contains following changes:
- check whether the device is really present
(we *can* probe for the device now).
Signed-off-by: Samuel Tardieu <sam@rfc1149.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This is patch 9 in the series of patches that converts
Marcus Junker's w83697hf watchdog driver to Samuel Tardieau's
w83697hf/hg watchdog driver.
This patch contains following changes:
- add w83697hf_get_reg() and w83697hf_set_reg()
functions.
Signed-off-by: Samuel Tardieu <sam@rfc1149.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This is patch 8 in the series of patches that converts
Marcus Junker's w83697hf watchdog driver to Samuel Tardieau's
w83697hf/hg watchdog driver.
This patch contains following changes:
- add w83697hf_lock function to leave the
chipsets extended function mode.
Signed-off-by: Samuel Tardieu <sam@rfc1149.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This is patch 7 in the series of patches that converts
Marcus Junker's w83697hf watchdog driver to Samuel Tardieau's
w83697hf/hg watchdog driver.
This patch contains following changes:
- add w83697hf_unlock function to enter the
chipsets extended function mode.
Signed-off-by: Samuel Tardieu <sam@rfc1149.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This is patch 6 in the series of patches that converts
Marcus Junker's w83697hf watchdog driver to Samuel Tardieau's
w83697hf/hg watchdog driver.
This patch contains following changes:
- The driver works for both the w83697hf
and the w83697hg chipset's.
Signed-off-by: Samuel Tardieu <sam@rfc1149.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This is patch 5 in the series of patches that converts
Marcus Junker's w83697hf watchdog driver to Samuel Tardieau's
w83697hf/hg watchdog driver.
This patch contains following changes:
- Rename the Extended Function Registers to the names
used in the data-sheet.
Signed-off-by: Samuel Tardieu <sam@rfc1149.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This is patch 4 in the series of patches that converts
Marcus Junker's w83697hf watchdog driver to Samuel Tardieau's
w83697hf/hg watchdog driver.
This patch contains following changes:
- limits the watchdog timeout to 1-63 while this
device accepts 1-255.
Signed-off-by: Samuel Tardieu <sam@rfc1149.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This is patch 3 in the series of patches that converts
Marcus Junker's w83697hf watchdog driver to Samuel Tardieau's
w83697hf/hg watchdog driver.
This patch contains following changes:
- Fix identation.
Signed-off-by: Samuel Tardieu <sam@rfc1149.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This is patch 2 in the series of patches that converts
Marcus Junker's w83697hf watchdog driver to Samuel Tardieau's
w83697hf/hg watchdog driver.
This patch contains following changes:
- wdt_io is 2 bytes long. We should do a
request_region for 2 bytes instead of 1.
Signed-off-by: Samuel Tardieu <sam@rfc1149.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This is patch 1 in the series of patches that converts
Marcus Junker's w83697hf watchdog driver to Samuel Tardieau's
w83697hf/hg watchdog driver.
This patch contains following changes:
- the note concerning tyan motherboards has been copied from
another driver, This doesn't apply here.
- the comments concerning CRF6 are wrong as CRF3 is manipulated
and CRF6 is never read nor written.
- the comments concerning CRF5 are wrong as CRF4 is manipulated
and CRF5 is never read nor written.
Signed-off-by: Samuel Tardieu <sam@rfc1149.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Return ENOTTY instead of ENOIOCTLCMD in user-visible ioctl() results
The watchdog drivers used to return ENOIOCTLCMD for bad ioctl() commands.
ENOIOCTLCMD should not be visible by the user, so use ENOTTY instead.
Signed-off-by: Samuel Tardieu <sam@rfc1149.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Add io spinlocks to prevent possible race
conditions between start and stop operations
that are issued from different child processes
where the master process opened /dev/watchdog.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
* Added io spinlocking
* Deleted WATCHDOG_MINOR (it's in the miscdevice include
* Changed timer_enabled to use set_bit functions
* WDIOC_GETSUPPORT should return -EFAULT or 0
* timeout should be correct before we initialize the watchdog
* we should initialize the watchdog before we give access
to userspace
* Third parameter of module_param is not the default or
initial value
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Retry internal operation after unit check instead of aborting them.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add timeout handler for common-I/O-layer-internal I/O operations.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The include of linux/smp.h needs to be done before the #if that
checks for the compiler version. Seems like fallout from the
inline assembly cleanup patch vs. the directed yield patch.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix a race condition during AP device registration and unregistration.
Signed-off-by: Ralph Wuerthner <rwuerthn@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
While the machine owns us an interrupt in these cases (and we should get
one), reality isn't always like that...
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix new restore_sigregs function. It copies the user space copy of the
old psw without correcting the psw.mask and the psw.addr high order bit.
While we are at it, simplify save_sigregs a bit.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* 'for-2.6.19' of git://brick.kernel.dk/data/git/linux-2.6-block:
[PATCH] Document bi_sector and sector_t
[PATCH] helper function for retrieving scsi_cmd given host based block layer tag
This was necessitated by the need for a function to get back
to a scsi_cmnd, when an hba the posts its (corresponding) completion
interrupt with a block layer tag as its reference.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: David Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* master.kernel.org:/pub/scm/linux/kernel/git/mchehab/v4l-dvb:
V4L/DVB (4712): Fix warning when compiling on x86_i64
V4L/DVB (4711): Radio: No need to return void
V4L/DVB (4708): Add tveeprom support for Philips FM1236/FM1216ME MK5
V4L/DVB (4707): 4linux: complete conversion to hotplug safe PCI API
V4L/DVB (4706): Do not enable VIDEO_V4L2 unconditionally
V4L/DVB (4704): SAA713x: fixed compile warning in SECAM fixup
V4L/DVB (4703): Add support for the ASUS EUROPA2 OEM board
V4L/DVB (4702): Fix: set antenna input for DVB-T for Asus P7131 Dual hybrid
V4L/DVB (4701): Saa713x audio fixes
V4L/DVB (4676a): Remove Kconfig item for DiB7000M support
The atmel_console_get_options() function initializes the baud,
parity and bits settings from the actual hardware setup, in
case it has been initialized by a e.g. boot loader.
The baud rate, however, is not necessarily exactly equal to one of
the standard baud rates (115200, etc.) This means that the baud rate
calculated by this function may be slightly higher or slightly lower
than one of the standard baud rates.
If the baud rate is slightly lower than the target, this causes
problems when uart_set_option() tries to match the detected baud rate
against the standard baud rate, as it will always select a baud rate
that is lower or equal to the target rate. For example if the
detected baud rate is slightly lower than 115200, usart_set_options()
will select 57600.
This patch fixes the problem by subtracting 1 from the value in BRGR
when calculating the baud rate. The detected baud rate will thus
always be higher than the nearest standard baud rate, and
uart_set_options() will end up doing the right thing.
Tested on ATSTK1000 and AT91RM9200-EK boards. Both are broken without
this patch.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Allow the board to remap actual USART peripheral devices to serial
devices by calling at32_map_usart(hw_id, serial_line). This ensures
that even though ATSTK1002 uses USART1 as the first serial port, it
will still have a ttyS0 device.
This also adds a board-specific early setup hook and moves the
at32_setup_serial_console() call there from the platform code.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make CONFIG_SERIAL_ATMEL selectable on AVR32 and #ifdef out some ARM-
specific code in the driver.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In order to initialize the serial console early, the atmel_serial
driver had to do a hack where it compared the physical address of the
port with an address known to be permanently mapped, and used it as a
virtual address. This got around the limitation that ioremap() isn't
always available when the console is being initalized.
This patch removes that hack and replaces it with a new "regs" field
in struct atmel_uart_data that the board-specific code can initialize
to a fixed virtual mapping for platform devices where this is possible.
It also initializes the DBGU's regs field with the address the driver
used to check against.
On AVR32, the "regs" field is initialized from the physical base
address when this it can be accessed through a permanently 1:1 mapped
segment, i.e. the P4 segment.
If regs is NULL, the console initialization is delayed until the "real"
driver is up and running and ioremap() can be used.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Rename at91_register_uart_fns and associated structs and variables
to make it consistent with the atmel_ prefix used by the rest of
the driver.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The at91_serial driver can be used with both AT32 and AT91 devices
from Atmel and has therefore been renamed atmel_serial. The only
thing left is to rename PORT_AT91 PORT_ATMEL.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
