Report all bad FCS errs as frames errs. This includes frames with bad
FCS on wire detected by MAC and frames which may be truncated due to
ingress FIFO overruns. No longer print a driver msg on bad FCS err.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return notify intr credits after notify intr from firmware. This is
especially important for legacy PCI intr mode, where not returning
credits would cause PBA to remain asserted which would get us right
back into the ISR.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PPP is modular code so no initdata on netns hooks.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the user creates IPv6 over IPv6 tunnel, the device name created
by the kernel isn't set to t->parm.name, which is referred as the
result of ioctl().
Signed-off-by: Noriaki TAKAMIYA <takamiya@po.ntts.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ira Snyder found that commit 8c7396aebb
"gianfar: Merge Tx and Rx interrupt for scheduling clean up ring" can
cause hangs. It's because there was removed clearing of interrupts in
gfar_schedule_cleanup() (which is called by an interrupt handler) in
case when netif scheduling has been disabled. This patch brings back
this action and a comment.
Reported-by: Ira Snyder <iws@ovro.caltech.edu>
Reported-by: Peter Korsgaard <jacmet@sunsite.dk>
Bisected-by: Ira Snyder <iws@ovro.caltech.edu>
Tested-by: Peter Korsgaard <jacmet@sunsite.dk>
Tested-by: Ira Snyder <iws@ovro.caltech.edu>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When user tries to map all chunks given in argument, kernel
works on a copy of the chunkmap, but at the end it doesn't
check the copy, but the orginal one.
Signed-off-by: Qu Haoran <haoran.qu@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes echoing if the socket that has sent the request to
create/update/delete an entry is not subscribed to any multicast
group. With the current code, ctnetlink would not send the echo
message via unicast as nfnetlink_send() would be skip.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes an inconsistency in the current ctnetlink code
since NAT sequence adjustment bit can only be updated but not set
in the conntrack entry creation.
This patch is used by conntrackd to successfully recover newly
created entries that represent connections with helpers and NAT
payload mangling.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes connection tracking handling for ICMPv6 messages
related to Stateless Address Autoconfiguration, MLD, and MLDv2. They
can not be tracked because they are massively using multicast (on
pre-defined address). But they are not invalid and should not be
detected as such.
Signed-off-by: Eric Leblond <eric@inl.fr>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch fixes a typo in the inverse mapping of Node Information
request. Following draft-ietf-ipngwg-icmp-name-lookups-09, "Querier"
sends a type 139 (ICMPV6_NI_QUERY) packet to "Responder" which answer
with a type 140 (ICMPV6_NI_REPLY) packet.
Signed-off-by: Eric Leblond <eric@inl.fr>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
gro: Optimise TCP packet reception
As this function can be called more than half a million times for
10GbE, it's important to optimise it as much as we can.
This patch uses bit ops to logical ops, as well as open coding
memcmp to exploit alignment properties.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
As this function can be called more than half a million times for
10GbE, it's important to optimise it as much as we can.
This patch does some obvious changes to use 2-byte and 4-byte
operations instead of byte-oriented ones where possible. Bit
ops are also used to replace logical ops to reduce branching.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch optimises the Ethernet header comparison to use 2-byte
and 4-byte xors instead of memcmp. In order to facilitate this,
the actual comparison is now carried out by the callers of the
shared dev_gro_receive function.
This has a significant impact when receiving 1500B packets through
10GbE.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch prepares for the move of the same_flow checks out of
dev_gro_receive. As such we need to remember the number of held
packets since doing a loop just to count them every time is silly.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several devices need to insert some "pre headers" in front of the
main packet data when they transmit a packet.
Currently we allocate only 16 bytes of pad room and this ends up not
being enough for some types of hardware (NIU, usb-net, s390 qeth,
etc.)
So increase this to 32.
Note that drivers still need to check in their transmit routine
whether enough headroom exists, and if not use skb_realloc_headroom().
Tunneling, IPSEC, and other encapsulation methods can cause the
padding area to be used up.
Signed-off-by: David S. Miller <davem@davemloft.net>
o Cut down msi-x vectors from 8 to 1 since only one is used for now.
o Use separate handler for msi-x, that doesn't unnecessarily scrub
msi status register.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DescOwn should not be set, thus allowing the chip to use the
descriptor, before everything else is set up correctly.
Signed-off-by: Risto Suominen <Risto.Suominen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tap devices can make use of a small MAC filter set via the
TUNSETTXFILTER ioctl. The filter has a set of exact matches
plus a hash for imperfect filtering of additional multicast
addresses. The current code is unbalanced, adding unicast
addresses to the multicast hash, but only checking the hash
against multicast addresses. This results in the filter
dropping unicast addresses that overflow the exact filter.
The fix is simply to disable the filter by leaving count set
to zero if we find non-multicast addresses after the exact
match table is filled.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Error handling code following a kmalloc should free the allocated data.
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,l;
position p1,p2;
expression *ptr != NULL;
@@
(
if ((x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...)) == NULL) S
|
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
)
<... when != x
when != if (...) { <+...x...+> }
x->f = E
...>
(
return \(0\|<+...x...+>\|ptr\);
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Error handling code following a kmalloc should free the allocated data.
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,l;
position p1,p2;
expression *ptr != NULL;
@@
(
if ((x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...)) == NULL) S
|
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
)
<... when != x
when != if (...) { <+...x...+> }
x->f = E
...>
(
return \(0\|<+...x...+>\|ptr\);
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the version number to 1.3.16 and update copyright dates for 2009.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch addresses two minor items I found while cleaning up the igb
driver for our sourceforge version.
The first clears the context index if we don't flag that we need it.
The second item is that eims_other should be used instead of bit defines
when setting all of the EICS bits prior to reset.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was seen with repeated interface up/down testing that there was a large
stray between the stats reported by the queues and the stats reported by the
HW. It was found to be an issue in that hw stats were being reset without
first being recorded. This change records the stats before wiping them from
the system via the reset.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the setting of ring->count variables from igb_probe as they are
duplicating the same configuration that is done igb_alloc_queues.
Remove the err_hw_init tag as it can be replaced by err_sw_init.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The disable_av variable is never used by the driver and provides no value as
it is likely a leftover debugging variable. I have removed it and replaced
the one spot that checked for it with a check for a valid address.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As additional hardware is added to the igb driver it is easier to support
the expansion via switch statements instead of using nested ifs. For
this reason I am changing this to a switch statement.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move igb_get_hw_control up so that it is called just after the reset in
igb_resume. This notifies the HW sooner that the driver is reassuming
control of the device.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupt handler was reading eicr and then doing nothing with the
result. I have removed the variable and the register read since they
provide no value to the legacy interrupt handler.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were several spots in the code making calls to adapter->hw when they
could have just been accessing hw-> directly. I cleaned up the spots where
this was visibly apparent.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There isn't much point in having the _82575 hanging off the end of this
function since there aren't any other version of this function running
around within this driver. This also allows for a bit of whitespace
cleanup due to a shorter function name.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The igb watchdog task is modifying the watchdog timer twice duing a single
run. It only needs to be called once to reschedule itself for 2 seconds from
the last time it ran.
In addition I removed the allocation of the mac_info structure since it is
only called twice and is easier to access via the e1000_hw struct.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleans up igb_netpoll so that it is more friendly with both the
current napi and newly introduced GRO features.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a counter for dma out of sync errors reported via interrupt.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the code for the testing has pretty much become stale at this point
and is need of update. This update just streamlines most of the code,
widens the range of interrupt testing.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver is currently using HW_CSUM which is not correct. Update this
to use the IP_CSUM and IPV6_CSUM flags. In addition consolidate the TSO
flag setting.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This statistic is not used and so it is safe to remove
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All of the nvm ops have the tag _nvm added to the end which is redundant
since all of the calls to the ops have to go through the nvm ops struct
anyway.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch renames write_phy_reg to write_reg and read_phy_reg to read_reg.
It seems redundant to call out phy in an operation that is part of the
phy_ops struct.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of pulling the mac address from EEPROM it is easier to pull it from
the RAL/RAH registers and then just copy it into the address structures.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes dev_spec a union and simplifies it so that it does not
require dynamic allocation and freeing in the driver.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a link check function to contain all activities related to verifying
that the link is present. The current approach is a bit cludgy and needs
to be cleaned up.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since igb supports only pci-e nics and there is no plan to support any
legacy pci parts in the driver there isn't really much need for checking to
see if an io port is needed.
In the unlikely event that we do begin supporting legacy pci parts then we
can see about adding this code back to the driver.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the initialization of the number of queues into
set_interrupt_capability. This allows the number of queues to increase in
the unlikely event that the system initially fails to allocate enough msi-x
interrupts, does a suspend/resume, and then can allocate enough interrupts
on resume.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
buffsz is being repeatedly set when allocaing buffers. Since this value
should only need to be set once in the function I am moving it out of the
looped portion of the path.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While cleaning up the skb_over panic with small frames I found there was
room for improvement in the ordering of operations within the rx receive
flow. These changes will place the prefetch for the next descriptor to a
point earlier in the rx path.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unfortunately, the OF device tree nodes for SBUS and PCI
hme devices have the same device node name on some systems.
So if the name of the parent node isn't 'sbus', skip it.
Based upon an excellent report and detective work by
Meelis Roos and Eric Brower.
Signed-off-by: David S. Miller <davem@davemloft.net>
Tested-by: Meelis Roos <mroos@linux.ee>
