Commit Graph

97778 Commits

Author SHA1 Message Date
Dan Williams
c337869d95 md: do not compute parity unless it is on a failed drive
If a block is computed (rather than read) then a check/repair operation
may be lead to believe that the data on disk is correct, when infact it
isn't.  So only compute blocks for failed devices.

This issue has been around since at least 2.6.12, but has become harder to
hit in recent kernels since most reads bypass the cache.

echo repair > /sys/block/mdN/md/sync_action will set the parity blocks to the
correct state.

Cc: <stable@kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-06-06 11:29:08 -07:00
Dan Williams
a6d8113a98 md: fix uninitialized use of mddev->recovery_wait
If an array was created with --assume-clean we will oops when trying to
set ->resync_max.

Fix this by initializing ->recovery_wait in mddev_find.

Cc: <stable@kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-06-06 11:29:08 -07:00
Dan Williams
e0a115e5aa md: fix prexor vs sync_request race
During the initial array synchronization process there is a window between
when a prexor operation is scheduled to a specific stripe and when it
completes for a sync_request to be scheduled to the same stripe.  When
this happens the prexor completes and the stripe is unconditionally marked
"insync", effectively canceling the sync_request for the stripe.  Prior to
2.6.23 this was not a problem because the prexor operation was done under
sh->lock.  The effect in older kernels being that the prexor would still
erroneously mark the stripe "insync", but sync_request would be held off
and re-mark the stripe as "!in_sync".

Change the write completion logic to not mark the stripe "in_sync" if a
prexor was performed.  The effect of the change is to sometimes not set
STRIPE_INSYNC.  The worst this can do is cause the resync to stall waiting
for STRIPE_INSYNC to be set.  If this were happening, then STRIPE_SYNCING
would be set and handle_issuing_new_read_requests would cause all
available blocks to eventually be read, at which point prexor would never
be used on that stripe any more and STRIPE_INSYNC would eventually be set.

echo repair > /sys/block/mdN/md/sync_action will correct arrays that may
have lost this race.

Cc: <stable@kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-06-06 11:29:08 -07:00
David Brownell
b2c8daddcb spi: fix refcount-related spidev oops-on-rmmod
This addresses other oopsing paths in "spidev" by changing how it manages
refcounting.  It decouples the lifecycle of the per-device data from the
class device (not just the spi device):

  - Use class_{create,destroy} not class_{register,unregister}.
  - Use device_{create,destroy} not device_{register,unregister}.
  - Free the per-device data only when TWO conditions are true:
      * Driver is unbound from underlying SPI device, and
      * Device is no longer open (new)

Also, spi_{get,set}_drvdata not dev_{get,set}_drvdata for simpler code.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Sebastian Siewior <bigeasy@tglx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-06-06 11:29:08 -07:00
Linus Torvalds
39b945a37b Merge master.kernel.org:/home/rmk/linux-2.6-arm
* master.kernel.org:/home/rmk/linux-2.6-arm:
  [ARM] pxa: fix tosa.c build error
  [ARM] 5067/1: _raw_write_can_lock macro bugfix
  [ARM] 5070/1: pxa: add GPIO104_PSKTSEL to pxa27x MFP configuration
  [ARM] 5068/1: PXA2xx Additional gpio definitions
  [ARM] 5066/2: EM-X270: Fix DM9000 IRQ flags initialisation
  [ARM] 5065/2: CM-X270: Fix DM9000 IRQ flags initialisation
  [ARM] 5062/1: pxa: remove unused definition of CONFIG_ARCH_COTULLA_IDP
  [ARM] 5060/1: remove unnecessary include of asm/io.h
  [ARM] fix AT91 include loops
2008-06-05 16:15:00 -07:00
Ben Collins
203c80187e mmc: Fix crash in mmc_block on 64-bit
Fairly simple. "dev_use" was being allocated as a zero length array
because of bad math on 64-bit systems, causing a crash in
find_first_zero_bit(). One-liner follows:

Signed-off-by: Ben Collins <ben.collins@canonical.com>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-06-05 16:14:17 -07:00
Linus Torvalds
b2ab26ab28 Merge git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb
* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (48 commits)
  V4L/DVB (8001): dib0070: fix dib0070_attach when !CONFIG_DVB_TUNER_DIB0070
  V4L/DVB (8000): tda827x: fix NULL pointer in tda827xa_lna_gain
  V4L/DVB (7990): Fix entry for PowerColor RA 330 and make it run with firmware version 2.7
  V4L/DVB (7983): tda18271_calc_rf_cal must return the return value of tda18271_lookup_map
  V4L/DVB (7978): cx18: explicitly test for XC2028 tuner
  V4L/DVB (7977): cx18: fix init order and remove duplicate open_on_first_use.
  V4L/DVB (7975): saa7134_empress
  V4L/DVB (7974): fix MEDIA_TUNER && FW_LOADER build error
  V4L/DVB (7972): or51132.c: unaligned
  V4L/DVB (7971): usb: unaligned
  V4L/DVB (7970): mix trivial endianness annotations
  V4L/DVB (7969): m920x: unaligned access
  V4L/DVB (7968): zoran: endianness annotations
  V4L/DVB (7967): bt8xx: unaligned access
  V4L/DVB (7966): cx18: direct dereferencing of iomem
  V4L/DVB (7965): annotate bcx_riscmem
  V4L/DVB (7964): cx18 iomem annotations
  V4L/DVB (7963): ivtv: trivial annotations
  V4L/DVB (7962): ttusb endianness annotations and fixes
  V4L/DVB (7961): fix endianness bug in dib0700_devices.c
  ...
2008-06-05 14:30:47 -07:00
Linus Torvalds
5965087dc9 Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  Fix divide by zero error in build_clear_page() and build_copy_page()
  [MIPS] Fix typo in header guard
  [MIPS] Fix build error - Delete debugging crap that crept in with CMP
  [MIPS] Add accessors for random register.
  [MIPS] IP27: misc fixes
  [MIPS] IP27: Fix clockevent setup
  [MIPS] IP27: Fix bootmem memory setup
  [MIPS] remove CONFIG_CPU_R4000 line from Makefile
  [MIPS] Fix check for valid stack pointer during backtrace
  [MIPS] Add missing braces to pte_mkyoung
  [MIPS] R4700: Fix build_tlb_probe_entry
  [MIPS] Alchemy: dbdma: add API to delete custom DDMA device ids.
  [MIPS] Alchemy: export get_au1x00_speed for modules
2008-06-05 14:29:53 -07:00
Linus Torvalds
698f7a4a12 Merge git://git.infradead.org/~dwmw2/mtd-2.6.26
* git://git.infradead.org/~dwmw2/mtd-2.6.26:
  [MTD] [MAPS] Fix cmdlineparse handling in mapping files
  [MTD] [NAND] pxa: fix incorrect calling of pxa3xx_nand_config() on resume path
2008-06-05 14:25:48 -07:00
Willy Tarreau
adbd5886da doc: add suggestions about good practises for maintainers
Suggest how to deal with patch modifications caused by
merging or back-porting when you're a maintainer.

Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-06-05 14:25:24 -07:00
Chris Wright
ddb2c43594 asn1: additional sanity checking during BER decoding
- Don't trust a length which is greater than the working buffer.
  An invalid length could cause overflow when calculating buffer size
  for decoding oid.

- An oid length of zero is invalid and allows for an off-by-one error when
  decoding oid because the first subid actually encodes first 2 subids.

- A primitive encoding may not have an indefinite length.

Thanks to Wei Wang from McAfee for report.

Cc: Steven French <sfrench@us.ibm.com>
Cc: stable@kernel.org
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-06-05 14:24:54 -07:00
Nick Piggin
efedf51c86 Add 'rd' alias to new brd ramdisk driver
Alias brd to rd in the hope of helping legacy users. Suggested by Jan.

Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-06-05 14:23:12 -07:00
Stefan Richter
16104b5504 x86: fix CONFIG_NONPROMISC_DEVMEM prompt and help text
Here is an attempt to translate the prompt and help text into something
which is legible and, as a bonus, correct.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-06-05 14:21:45 -07:00
David Howells
609a70ac92 FRV: ip_fast_csum() requires a memory clobber on its inline asm
ip_fast_csum() requires a memory clobber on its inline asm as it accesses
memory in a fashion that gcc can't predict.

The GCC manual says:

 If your assembler instructions access memory in an unpredictable
 fashion, add `memory' to the list of clobbered registers.  This will
 cause GCC to not keep memory values cached in registers across the
 assembler instruction and not optimize stores or loads to that memory.

The bug hasn't been noticed in FRV, but it has been seen in PA-RISC.

Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-06-05 10:31:21 -07:00
Bjorn Helgaas
5a515bcbea PNP: skip UNSET MEM resources as well as DISABLED ones
We don't need to reserve "unset" resources.  Trying to reserve
them results in messages like this, which are ugly but harmless:

    system 00:08: iomem range 0x0-0x0 could not be reserved

Future PNP patches will remove use of IORESOURCE_UNSET, but
we still need it for now.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-06-05 10:30:37 -07:00
Yoichi Yuasa
cd9da13d6e Fix divide by zero error in build_clear_page() and build_copy_page()
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2008-06-05 18:13:16 +01:00
Vegard Nossum
2cc3c0b67b [MIPS] Fix typo in header guard
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2008-06-05 18:13:16 +01:00
Ralf Baechle
482845a348 [MIPS] Fix build error - Delete debugging crap that crept in with CMP
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2008-06-05 18:13:16 +01:00
Ralf Baechle
272bace7f3 [MIPS] Add accessors for random register.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2008-06-05 18:13:15 +01:00
Thomas Bogendoerfer
96173a6c4e [MIPS] IP27: misc fixes
- fix PCI interrupt assignment by emulating ioc3 interrupt pin register
- use pci_probe_only mode
- select correct page size in bridge
- remove no longer needed ioc3_sio_init() code

[Ralf: Fix for 64kB or larger pagesizes]

Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2008-06-05 18:13:15 +01:00
Thomas Bogendoerfer
b32bb803fb [MIPS] IP27: Fix clockevent setup
Fix breakage introduced by converting hub_rt to clockevent.

Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2008-06-05 18:13:14 +01:00
Thomas Bogendoerfer
2bf8ec2d81 [MIPS] IP27: Fix bootmem memory setup
Changes in the generic bootmem code broke memory setup for IP27. This
patch fixes this by replacing lots of special IP27 code with generic
bootmon code. This has been tested only on a single node.

Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2008-06-05 18:13:14 +01:00
Adrian Bunk
c2719d9383 [MIPS] remove CONFIG_CPU_R4000 line from Makefile
The existing options are named CONFIG_CPU_R4300 and CONFIG_CPU_R4X00,
and they are directly below.

Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2008-06-05 18:13:14 +01:00
Thomas Bogendoerfer
10220c8844 [MIPS] Fix check for valid stack pointer during backtrace
The newly added check for valid stack pointer address breaks at least for
64bit kernels.  Use __get_user() for accessing stack content to avoid crashes,
when doing the backtrace.

Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2008-06-05 18:13:14 +01:00
Ilpo Järvinen
057229f9ef [MIPS] Add missing braces to pte_mkyoung
Only the version pte_mkyoung for 36-bit pagetables on 32-bit hw was
affected and with this bug being around since November 29, 2004 there
is evidence to suport the assumption it was benign ;-)

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2008-06-05 18:13:14 +01:00
Thomas Bogendoerfer
326e2e1a59 [MIPS] R4700: Fix build_tlb_probe_entry
Treat R4700 like R4600 in build_tlb_probe_entry. Without this fix kernel
will lock up.

Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2008-06-05 18:13:14 +01:00
Manuel Lauss
ccdb0034f8 [MIPS] Alchemy: dbdma: add API to delete custom DDMA device ids.
Add API to delete custom DDMA device ids create with
au1xxx_ddma_device_add().

Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2008-06-05 18:13:14 +01:00
Manuel Lauss
b1fb05cdb9 [MIPS] Alchemy: export get_au1x00_speed for modules
au1xmmc.c driver depends on it, so export it for modules.

Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2008-06-05 18:13:13 +01:00
Hugh Dickins
6311c90a9e libata: fix G5 SATA broken on -rc5
Fix G5 SATA irq 18: nobody cared, reported on -rc5 by Olaf Hering:
fixlet to a57c1bade5 libata-sff:
Fix oops reported in kerneloops.org for pnp devices with no ctl

Signed-off-by: Hugh Dickins <hugh@veritas.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Tested-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-06-05 08:36:37 -07:00
Michael Krufky
be573e7872 V4L/DVB (8001): dib0070: fix dib0070_attach when !CONFIG_DVB_TUNER_DIB0070
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-05 10:26:21 -03:00
Sigmund Augdal
67642a0a58 V4L/DVB (8000): tda827x: fix NULL pointer in tda827xa_lna_gain
Check that tda827x_config is defined before attempting to use it.

Signed-off-by: Sigmund Augdal <sigmund@snap.tv>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-05 10:26:19 -03:00
Daniel Gimpelevich
a9606ce697 V4L/DVB (7990): Fix entry for PowerColor RA 330 and make it run with firmware version 2.7
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-05 06:35:56 -03:00
Michael Krufky
fc60d6e272 V4L/DVB (7983): tda18271_calc_rf_cal must return the return value of tda18271_lookup_map
On the TDA18271HD/C1, we perform RF tracking filter correction for VHF low
band, only. If supplied a frequency out of range, the error must be returned
to the caller (tda18271c1_rf_tracking_filter_calibration) so that it can
decide whether or not to write to register EB14, RFC_CPROG[7:0]

Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-05 06:35:54 -03:00
Hans Verkuil
4ecc247377 V4L/DVB (7978): cx18: explicitly test for XC2028 tuner
Testing whether xceive_pin is non-zero is not good enough as 0 is a valid
value. Instead explicitly test whether the Xceive tuner is used.

Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-05 06:35:54 -03:00
Hans Verkuil
5e7fdc5ed8 V4L/DVB (7977): cx18: fix init order and remove duplicate open_on_first_use.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-05 06:35:54 -03:00
Dmitri Belimov
388748e61c V4L/DVB (7975): saa7134_empress
This is patch for fix data structure in querycap syscall.

Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-05 06:35:54 -03:00
Ingo Molnar
6637dea60e V4L/DVB (7974): fix MEDIA_TUNER && FW_LOADER build error
-tip testing found the following build failure:

  LD      .tmp_vmlinux1
  drivers/built-in.o: In function `generic_set_freq':
  tuner-xc2028.c:(.text+0xbd896): undefined reference to `request_firmware'
  tuner-xc2028.c:(.text+0xbdd7a): undefined reference to `release_firmware'
  drivers/built-in.o: In function `xc_load_fw_and_init_tuner':
  xc5000.c:(.text+0xc68e6): undefined reference to `request_firmware'
  xc5000.c:(.text+0xc6abe): undefined reference to `release_firmware'

with this config:

  http://redhat.com/~mingo/misc/config-Tue_May_20_18_11_34_CEST_2008.bad

the reason is another kconfig tool bug that has to be worked around in
the driver's Kconfig file: if FW_LOADER is selected in a second
dependency, that is not properly propagated up the dependencies.

in this case, FW_LOADER is selected from MEDIA_TUNER_XC2028:

  config MEDIA_TUNER_XC2028
        tristate "XCeive xc2028/xc3028 tuners"
        depends on VIDEO_MEDIA && I2C
        depends on HOTPLUG
        select FW_LOADER

which got selected by MEDIA_TUNER:

  config MEDIA_TUNER
        tristate
        default VIDEO_MEDIA && I2C
        depends on VIDEO_MEDIA && I2C
        select FW_LOADER if !MEDIA_TUNER_CUSTOMIZE && HOTPLUG

but the kconfig tool did not pick up this second-order dependency and
allowed CONFIG_FW_LOADER=m to be selected - in which case the build
fails.

the workaround i found was to move the select of FW_LOADER one level up,
so that the buggy kconfig tool can notice it and can act appropriately.
This problem can probably be worked around in other ways as well, i went
for the minimal fix.

Obviously, the kconfig tool should be fixed, it is not reasonable to
expect driver authors to do manual dependency resolution (that kconfig
itself already does) and uglify the Kconfig files. The kconfig tool did
nothing to warn about this situation and did not prevent this faulty
.config from being constructed.

Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-05 06:35:53 -03:00
Al Viro
18dcd55a8b V4L/DVB (7972): or51132.c: unaligned
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-05 06:35:53 -03:00
Al Viro
637007fe5c V4L/DVB (7971): usb: unaligned
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-05 06:35:53 -03:00
Al Viro
a954b6681d V4L/DVB (7970): mix trivial endianness annotations
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-05 06:35:52 -03:00
Al Viro
fa9c13a383 V4L/DVB (7969): m920x: unaligned access
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-05 06:35:52 -03:00
Al Viro
581a7f1a2d V4L/DVB (7968): zoran: endianness annotations
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-05 06:35:52 -03:00
Al Viro
c1c36f3128 V4L/DVB (7967): bt8xx: unaligned access
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-05 06:35:52 -03:00
Al Viro
576904bb89 V4L/DVB (7966): cx18: direct dereferencing of iomem
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-05 06:35:51 -03:00
Al Viro
d8eaa58b06 V4L/DVB (7965): annotate bcx_riscmem
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-05 06:35:51 -03:00
Al Viro
990c81c8af V4L/DVB (7964): cx18 iomem annotations
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-05 06:35:49 -03:00
Al Viro
b0510f8dc7 V4L/DVB (7963): ivtv: trivial annotations
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-05 06:35:49 -03:00
Al Viro
d4f979a9e1 V4L/DVB (7962): ttusb endianness annotations and fixes
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-05 06:35:49 -03:00
Al Viro
da5ee48677 V4L/DVB (7961): fix endianness bug in dib0700_devices.c
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-05 06:35:49 -03:00
Al Viro
12fbcef105 V4L/DVB (7960): net: endianness annotations
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2008-06-05 06:35:48 -03:00