OPL3SA2 driver
- use different name (opl3sa2-pnpbios) for PnP BIOS driver
- don't print warning when manual config of resources fails (PnP BIOS)
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
AC97 Codec
Make the patch_wolfson_wm97??_specific() functions static again.
This patch was accidentally reverted in rev. 1.92.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
With the double buffering, we no longer need contiguous memory for the
PCM buffer, so we can use vmalloc() instead of the preallocation
functions, and increase the maximum size to 256 KB.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
Use the USB buffer allocation functions to avoid repeated DMA mappings
of our buffers, which are re-used quite a lot.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
Take the substream lock when reading hwptr_done to avoid a race
condition with the updates in the URB callbacks.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
Change prepare_playback_urb() not to stop preparing packets before a
frame boundary has been reached.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
We always had to use double buffering when capturing, and when playback
data for one URB crosses a buffer boundary. The latter would make hwptr
updates less precise because the double-buffered data is read from the
buffer much earlier than the other data is read by the host controller.
Double-buffering all data allows to update hwptr immediately after the
data was copied to the USB buffer(s), which has the additional benefit
of avoiding the latency imposed by the host controller's delay of up to
one frame when interrupting.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
When preparing capture URBs, we don't need to stop when we cross a
period boundary because we now never handle more than one millisecond of
data per URB anyway.
When handling captured data, use an extra flag to call
snd_pcm_period_elapsed() no more than once. This allows us to move the
period boundary checking code before the copying of the data which
avoids a second locking of the substream's lock.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
OPL3SA2 driver
The driver has been extended to support also PnP BIOS devices.
The detection path is:
1) detect PnP BIOS devices
2) detect ISA PnP devices
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
VIA82xx driver
Added the DXS entry for MSI K8MM-V.
Also fixed a typo in last patch for Acer Aspire 1524 WLMi.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
USB generic driver
The EHCI driver doesn't interrupt more than once per millisecond, and
organizes all iso transfers with frame-sized ITDs, so we can (try to)
be more efficient by aligning all URBs on frame boundaries.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
The nrpacks module parameter is used only when initializing a playback
stream, so it doesn't hurt to make it writeable.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
When determining how many packets are needed for one period, we cannot
assume that all packets have their maximum size -- we always use the
nominal sample rate when sending data, and could use an even lower rate
when the endpoint uses frequency feedback.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
USB generic driver
When capturing audio data, we do not know beforehand how many samples
the device sends per frame, so we have to use URBs that are as short as
possible to make sure that we can handle period boundaries without any
additional latencies.
Furthermore, the total count of URBs submitted doesn't matter when
capturing, so we can just use the maximum number.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Memalloc module,PCM Midlevel,Timer Midlevel,GUS Library,AC97 Codec
ALI5451 driver,RME9652 driver
Make some functions/variables that are used in only one file static.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
PCM Midlevel,ALSA<-OSS emulation,USB USX2Y
This patch removes open_flag from struct _snd_pcm_substream.
All of its uses are substituted by querying struct _snd_pcm_substream's
member ffile instead.
Signed-off-by: Karsten Wiese <annabellesgarden@yahoo.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
YMFPCI driver
Implements mixer controls for the volume of each playback substream of
the main PCM device.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
ARM PXA2XX driver
- change pxa2xx_ac97_do_suspend and pxa2xx_ac97_do_resume to use
the expected arguments
Signed-off-by: Dirk Opfer <dirk@do13.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AC97 Codec
This patch fixes a problem whereby the WM9713 has modem functionality
incorrectly detected after an AC97 cold reset.
Changes:-
o Cleared AC97_SCAP_MODEM in wm9713 scaps
Signed-off-by: Liam Girdwood <liam.girdwood@wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ARM PXA2XX driver
This patch extends the period of an AC97 warm reset on the PXA27x from
50uS to 500uS. The shorter reset didn't always guarantee that the codec
would wake up.
Changes:-
o Change pxa27x warm reset period to 500uS
o Removed double semi-colon.
Signed-off-by: Liam Girdwood <liam.girdwood@wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Documentation,AD1816A driver
Added clockfreq module option for the card with a different clock frequency
than 33kHz.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Digigram VX core,ENS1370/1+ driver,CA0106 driver,EMU10K1/EMU10K2 driver
RME HDSP driver,RME9652 driver
For consistency, use the PCM interface instead of MIXER for IEC958
default/mask/stream mixer controls.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
CMI8330 driver,ENS1370/1+ driver,FM801 driver,VIA82xx driver,AC97 Codec
ALI5451 driver,CS46xx driver,EMU10K1/EMU10K2 driver,HDA Codec driver
ICE1712 driver,ICE1724 driver
Where appropriate, use the SNDRV_CTL_NAME_IEC958 instead of a literal
string.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
ALSA Core
This patch adds the __init macro to snd_memory_init().
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AC97 Codec,PCI drivers
I've made the review changes and as requested I've pasted the RFC by
Nicolas below:-
'I would like to know what people think of the following patch. It
allows for a codec on an AC97 bus to be shared with other drivers which
are completely unrelated to audio. It registers a new bus type, and
whenever a codec instance is created then a device for it is also
registered with the driver model using that bus type. This allows, for
example, to use the extra features of the UCB1400 like the touchscreen
interface and the additional GPIOs and ADCs available on that chip for
battery monitoring. I have a working UCB1400 touchscreen driver here
that simply registers with the driver model happily working alongside
with audio features using this.'
Changes over RFC:-
o Now matches codec name within codec group.
o Added ac97_dev_release() to stop kernel complaining about no release
method for device.
o Added 'config SND_AC97_BUS' to sound/pci/Kconfig and moved 'config
SND_AC97_CODEC' out with the PCI=n statement.
o module is now called snd-ac97-bus
Signed-off-by: Liam Girdwood <liam.girdwood@wolfsonmicro.com>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Documentation,CS46xx driver,EMU10K1/EMU10K2 driver,AD1848 driver
SB16/AWE driver,CMIPCI driver,ENS1370/1+ driver,RME32 driver
RME96 driver,ICE1712 driver,ICE1724 driver,KORG1212 driver
RME HDSP driver,RME9652 driver
This patch changes .iface to SNDRV_CTL_ELEM_IFACE_MIXER whre _PCM or
_HWDEP was used in controls that are not associated with a specific PCM
(sub)stream or hwdep device, and changes some controls that got
inconsitent .iface values due to copy+paste errors. Furthermore, it
makes sure that all control that do use _PCM or _HWDEP use the correct
number in the .device field.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
HDA Codec driver
- Fixed the reordering of surround channels.
Originally reported by Nicolas GRAZIANO <nicolas.graziano@wanadoo.fr>.
- Show the selected ssid when debug option is set.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AC97 Codec
o Enhanced current WM97xx support to provide additional controls and
use the kcontrol suffix naming convention.
o Added AC97_HAS_NO_MIC, AC97_HAS_NO_TONE and AC97_HAS_NO_STD_PCM.
o Cleaned up WM97xx related comments.
o Removed some wm9713 double mono controls and replaced with stereo
controls.
Signed-off-by: Liam Girdwood <liam.girdwood@wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Damir Perisa <damir.perisa@solnet.ch> reports:
drivers/net/s2io.h:765: error: invalid lvalue in assignment
drivers/net/s2io.h:766: error: invalid lvalue in assignment
That's a gcc4 error. I don't see why the casts are there anyway..
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The {BEGIN,END}_FTR_SECTION asm macros used in ppc64 to nop out
sections of code at runtime cannot be nested. However, we do nest
them in hash_low.S. We get away with it there, because there is
nothing between the BEGIN markers for each section. However, that's
confusing to someone reading the code.
This patch removes the nested ifset and ifclr feature sections,
replacing them with a single feature section in the full mask/value
form.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch fixes a rare memory leak found by Coverity.
Signed-off-by: Joel Schopp <jschopp@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
While ppc64 has the CONFIG_HZ Kconfig option, it wasnt actually being
used. Connect it up and set all platforms to 250Hz.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Here's the 970MP's PVR (processor version register) entry for oprofile.
Signed-off-by: Jake Moilanen <moilanen@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some RS64-based machines (p620, F80, others) have problems with firmware
returning 0xdeadbeef instead of failure to allocations that end at the
1GB mark.
We have two options:
1. Detect the undocumented 0xdeadbeef return value and interpret it as
a failure.
2. Avoid allocating that high.
(2) is really the cleaner solution here. 768MB is plenty of room so use
that as the max alloc_top instead of 1GB.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
They differed in either simple comments or in the protecting ifdefs.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
