We don't use setup_indirect_pci_nomap in arch/powerpc and it appears
the users that needed it from arch/ppc are now using setup_indirect_pci.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On the 85xx/86xx PCIe controllers if there is no device connected to the
PHB we will still allocate a pci_bus for downstream bus of the virtual
P2P bridge. However the resources allocated to the downstream bus are not
correct and so we just mimic the resources from the upstream pci_bus.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Switch the 85xx platform over to using the FSL generic PCI code. This
gets ups PCIe support in addition to base PCI support.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use the PCI capabilities to determine if we are PCIe PHB. Also use
PPC_INDIRECT_TYPE_NO_PCIE_LINK since the Freescale PCIe controllers
will lock the system if they don't have link and you try to do a config
access to anything but the PHB.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Added PPC_INDIRECT_TYPE_NO_PCIE_LINK flag to the indirect pci handling
code to ensure that we don't talk to any device other than the PHB
if we don't have PCIe link. Some controllers will lockup if they try
to do a config cycle to any device on the bus except the PHB.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Rewrite the Freescale PCI code to support PCI on 83xx/85xx/86xx and
PCIe on 85xx/86xx.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Move
arch/powerpc/platforms/86xx/pci.c -> arch/powerpc/sysdev/fsl_pci.c
arch/powerpc/sysdev/fsl_pcie.h -> arch/powerpc/sysdev/fsl_pci.h
as the base to unify 83xx/85xx/86xx pci and pcie.
Add CONFIG_FSL_PCI to build fsl_pci.c for Freescale pci and pcie option.
The code still works for 86xx platforms.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some HW platforms, such as the new cell blades, requires some MPIC sources
to be left alone by the operating system. This implements support for
a "protected-sources" property in the mpic controller node containing a list
of source numbers to be protected against operating system interference.
For those interested in the gory details, the MPIC on the southbridge of
those blades has some of the processor outputs routed to the cell, and
at least one routed as a GPIO to the service processor. It will be used
in the GA product for routing some of the southbridge error interrupts
to the service processor which implements some of the RAS stuff, such
as checkstopping when fatal errors occurs before they can propagate.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The Axon bridge chip used on new Cell/B.E. based blade servers
comes with a DDR2 memory controller that can be used to
attach cheap memory modules, as opposed to the high-speed
XDR memory that is used by the CPU itself.
Since the memory controller does not participate in the
cache coherency protocol, we can not use the memory direcly
for Linux applications, but by providing a block device
it can be used for swap space, temporary file storage and
through the use of the direct_access block device operation
for mapping into user addresses, when it is mounted with
an appropriate file system.
Signed-off-by: Maxim Shchetynin <maxim@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
The pmi driver got simplified by removing support for multiple devices.
As there is no more than one pmi device per maschine, there is no need to
specify the device for listening and sending messages.
This way the caller (cbe_cpufreq) doesn't need to scan the device tree.
When registering the handler on a board without a pmi
interface, pmi.c will just return -ENODEV.
The patch that fixed the breakage of cell_defconfig has been
broken out of the earlier version of this patch. So this is
the version that applies cleanly on top of it.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
The TSEC/eTSEC can detect the interface to the PHY automatically,
but it isn't able to detect whether the RGMII connection needs internal
delay. So we need to detect that change in the device tree, propagate
it to the platform data, and then check it if we're in RGMII. This fixes
a bug on the 8641D HPCN board where the Vitesse PHY doesn't use the delay
for RGMII.
Signed-off-by: Andy Fleming <afleming@freescale.com>
In order to use the RTC CMOS driver, each architecture must register a
platform device for the RTC.
This creates a function to register the platform device based on the RTC
device node and verifies that the RTC port against the hard-coded value
in asm/mc146818rtc.h.
Signed-off-by: Wade Farnsworth <wfarnsworth@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Adds support for PowerQuicc on-chip PCMCIA. The driver is implemented as
of_device, so only arch/powerpc stuff is capable to use it, which now implies
only mpc885ads reference board.
To cope with the code that should be hooked inside driver, but is really board
specific (like set_voltage), global structure mpc8xx_pcmcia_ops holds
necessary function pointers that are filled in the BSP code.
[akpm@linux-foundation.org: whitespace diddles]
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Olof Johansson <olof@lixom.net>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Export symbols of qe_lib to be used by QE driver.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Selvamuthukumar V <vsmkumar.84@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Make the ppc32 pcibios_alloc_controller take a device node to match
the ppc64 prototypes and have it set arch_data.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale PCI-e controllers have an issue in that they use the
PCI_PRIMARY_BUS register in the virtual P2P bridge to determine which
bus number to match on when generating a type 0 config cycle. The
issue is if we are renumbering bus numbers to match Linux we will try
setting the PCI_PRIMARY_BUS and will not know which bus number to use
for generating type 0 config cycles. We surpress writing the register
in the P2P bridge and always keep it at zero.
In the future when proper PCI domain support is working we should be
able to remove this.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The generic PCI config ops indirect support for ppc32 covers only two
cases (implicit vs explicit) type 0/1 config cycles via set_cfg_type.
Added a indirect_type bit mask to handle other variants.
Added support for PCI-e extended registers and moved the cfg_type
handling into the bit mask for ARCH=powerpc. We can also use this to
handle indirect quirks.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove errata for PCI-e support of Rev 1.0 of MPC8641 since its considered
obselete and is not production level silicon from Freescale.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Acked-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Removed the remants of bus_offset and use self_busno in the mv64x60 case
and use pci_assign_all_buses on 83xx/85xx.
83xx/85xx have multiple PHBs and the firmwares on these devices tend not
to handle topologies with P2P bridges well so we let Linux just reassign
the bus numbers to match.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Added self_busno to pci_controller and indirect PCI ops to be set by
board code to indicate which bus number to use when talking to the PHB.
By default we use zero since the majority of controllers that have
implicit mechanisms to talk to the PHBs use a bus number of zero.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The user of the fsl_pcie code doesn't set bus_offset and 82xx doesn't
require it either. Remove the places in the code that reference it so
we can remove it all together.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There are times that we need to know which controller we are on to decide
how to exclude devices properly. We now pass the pci_controller that we
are going to use down to the pci_exclude_device function. This will
greatly simplify being able to exclude the PHBs in multiple controller
setups.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale and Marvell PCI controllers dont require explicit setting for
type 1 config cycles. They handle producing them by implicitly looking at the
bus, devfn.
The TSI108 and 52xx don't use the generic PCI indirect code and thus don't
bother with set_cfg_type.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When a Marvell MPSC (serial controller) port is the specified
/chosen/stdout-path device, call 'add_preferred_console()' so the user
doesn't have to specify a 'console=ttyMMx' cmdline argument.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
With both generic rtc and powerpc timer suspend / resume code now in the
(powerpc.git) tree, powerpc platforms using the generic timer and enabling
power management will have timer.o linked in the kernel, which they don't
need. Moreover, it will likely WARN_ON(!ppc_md.get_rtc_time), save
zero-time and return no error on suspend...
As a possible solution we can choose not to build timer.o when RTC_CLASS
is enabled. However, I can imagine systems with 2 rtc's, one served by the
ppc-rtc, another one generic built as a module, in which case using the
ppc-rtc for suspend / resume will be impossible. Not to say, that such a
configuration would be ugly...
Signed-off-by: G. Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This makes the timer sysdev use mktime instead of rtc_tm_to_time,
since rtc_tm_to_time just calls mktime anyway, and this means we
don't have a dependency on rtc-lib.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes some problems with the way the some things
represented in the device tree for the Holly and Taiga boards. This
means changes both to the dts files, and to the code which
instantiates the tsi108 ethernet platform devices based on the device
tree.
- First, and most importantly, the ethernet PHYs are given
with an identical 'reg' property. This reg currently encodes the
accessible register used to initiate mdio interaction with the PHYs,
rather than a meaningful address on the parent bus (mdio in this
case), which is incorrect. Instead we give the address of these
registers as 'reg' in the mdio node itself, and encode the ID of each
phy in their 'reg' propertyies.
- Currently the platform device constructor enables a
workaround in the tsi108 ethernet driver based on the compatible
property of the PHY. This is incorrect, because the workaround in
question is necessary due to the board's wiring of the PHY, not the
model of PHY itself. This patch alters the constructor to instead
enable the workaround based on a new special property in the PHY node.
- The compatible properties on a number of nodes in the device
tree are insufficiently precise. In particular the PHYs give only
"bcm54xx", which is broken, since there are many bcm54xx PHY models,
and they have differences which matter. The mdio had a compatible
property of "tsi-ethernet" identical to the ethernet MAC nodes, which
doesn't make sense. The ethernet, i2c, bridge and PCI nodes were
given only as "tsi-*" which is somewhat inprecise, we replace with
"tsi108-*" in the case of Taiga (which has a TSI108 bridge), and
"tsi109-*", "tsi108-*" in the case of Holly (which has a TSI109
bridge).
- We remove some "model" properties from the ethernets on
Taiga board which were neither useful nor adequately precise.
- On Holly we change to using a dtc label instead of a full
path to reference the MPIC node, which makes the dts a little more
readable.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The UCC_GETH Kconfig option in drivers/net/Kconfig had a line to select the
UCC_FAST option is arch/powerpc/sysdev/qe_lib/Kconfig, which is only used
on PowerPC builds. On other architectures, this would generated a warning.
The fix is to have UCC_FAST depend on UCC_GETH.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
arch/powerpc/sysdev/mpic.c: In function 'mpic_request_ipis':
arch/powerpc/sysdev/mpic.c:1445: warning: ignoring return value of 'request_irq', declared with attribute warn_unused_result
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds PCI bridge support for the Marvell mv64x60 chip.
We also provide the ability to read/write the mv64x60 hotswap
register via sysfs if the hs_reg_valid property is set in the
device tree.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch creates platform_device entries for the Marvell mv64x60
I2C ports, based on information contained in device tree.
This driver (like the other mv64x60 drivers) are unusual in that it
works on both the MIPS and PowerPC architectures. Because of that,
the drivers do not support the normal PowerPC of_platform_bus_type.
They support platform_bus_type instead.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch creates platform_device entries for the Marvell mv64x60
ethernet controller ports, based on information contained in the
device tree.
This driver (like the other mv64x60 drivers) are unusual in that it
works on both the MIPS and PowerPC architectures. Because of that,
the drivers do not support the normal PowerPC of_platform_bus_type.
They support platform_bus_type instead.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch creates platform_device entries for the Marvell mv64x60
MPSC (multi-protocol serial controller) ports, based on information
contained in the device tree.
This driver (like the other mv64x60 drivers) are unusual in that it
works on both the MIPS and PowerPC architectures. Because of that,
the drivers do not support the normal PowerPC of_platform_bus_type.
They support platform_bus_type instead.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There are 3 interrupt groups each with its own status/mask registers.
We use a separate struct irq_chip for each interrupt group and handle
interrupts in two stages or levels: level 1 selects the appropriate
struct irq_chip, and level 2 selects individual interrupts within
that irq_chip.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The rheap allocation functions return a pointer, but the actual value is based
on how the heap was initialized, and so it can be anything, e.g. an offset
into a buffer. A ulong is a better representation of the value returned by
the allocation functions.
This patch changes all of the relevant rheap functions to use a unsigned long
integers instead of a pointer. In case of an error, the value returned is
a negative error code that has been cast to an unsigned long. The caller can
use the IS_ERR_VALUE() macro to check for this.
All code which calls the rheap functions is updated accordingly. Macros
IS_MURAM_ERR() and IS_DPERR(), have been deleted in favor of IS_ERR_VALUE().
Also added error checking to rh_attach_region().
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
of_get_mac_address() returns a const pointer, so the result
should be stored in a const pointer.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
powerpc_flash_init() implements a broken way of probing for flash
devices supported by the physmap_of driver. It finds all nodes in the
device tree with device_type=="rom" and instantiates of_platform
devices for them. This is fundamentally incompatible with the normal
and correct way of probing for of_platform_bus_probe(). Platforms
which relied on powerpc_flash_init()s behaviour (none are in-tree)
will have to update their platform probing code to correctly probe
busses containing flash devices.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
MPIC U3/U4 MSI backend. Based on code from Segher, heavily hacked by me.
This only deals with MSI on U3/U4 MPICs, aka. CPC 9x5.
If we find a U3/U4 then we enable this backend, ie. take over the ppc_md
MSI hooks. We might need more elaborate logic in future to decide which
backend is enabled.
We need our own irq_chip so that we can do MSI masking/unmasking on
the device itself. We also need to mask explicitly on shutdown to make
sure we don't get bitten by lazy-disable semantics.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
To support MSI on MPIC we need a way to reserve and allocate hardware irq
numbers, this patch implements an allocator for that purpose.
New firmware platforms must define a "msi-available-ranges" property on their
MPIC node for MSI to work. For U3/U4 we do a best-guess setup.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On some Apple machines the HT MSI mappings are not enabled by firmware, so
we need to do it by hand.
We can't use the pci routines as this code runs too early.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Generalize tsi108_setup_pci to take the config space physical address and
primary bus designator as a parameter.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a phy_type field to the tsi108 ethernet structures to indicate which PHY
is used on a board. This is derived from the "compatible" property in the
ethernet-phy node of the device tree. The default remains the MV88E PHY.
Also, convert the setup code to use of_get_mac_address instead of hard coding
a lookup for the "address" property in the ethernet node.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a header file for the common PCI routines used for the TSI bridge
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This implements save and restore hooks for IOMMUs and implements
it the DART iommu.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
for consistency with other Open Firmware interfaces (and Sparc).
This is just a straight replacement.
This leaves the compatibility define in place.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds mpic to the system devices and implements suspend
and resume for them. This is necessary to get interrupts for
modules back to where they were before a suspend to disk.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The weird TSI 10x MPIC needs an EOI after getting a spurious vector. This
patch uses the existing MPIC_SPV_EOI flag to fix this issue.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
arch/powerpc/sysdev/timer.c:51: error: variable `timer_sysclass' has
initializer but incomplete type
arch/powerpc/sysdev/timer.c:52: error: unknown field `resume' specified in initializer
<etc>
Signed-off-by: Srinivasa Ds <srinivasa@in.ibm.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
