Two files were omitted from the recent removal of the qemu platform.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch enables the system calls timerfd_create(), timerfd_settime()
and timerfd_gettime() for MIPS architecture.
Please see the following Bugzilla entry for more details:
http://bugzilla.kernel.org/show_bug.cgi?id=10038
This was tested using a Malta 4Kc board in both little-endian and
big-endian modes. The unit test program is available from the URL
above.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
[Ralf: Added N64, N32 and O32 bits on 64-bit kernels.]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix type mismatch warnings for 64-bit kernel builds which trigger -Werror.
The problem affects only SB-1 kernels with CONFIG_SIBYTE_DMA_PAGEOPS
enabled.
Signed-off-by: Thiemo Seufer <ths@networkno.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
kmap_coherent will only work correctly if the page it is called on is
not marked dirty. If it's dirty the kernel address of the page should
be used instead of a temporary mapping.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Properly acknowledge RM7K and RM9K interrupts. Before this, interrupts were
permanently masked after their first occurrence, making them non-functional.
Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
So far flush_cache_range() did't consider the I-cache largely because it
did rarely ever matter to real world code. This was working primarily
because normally code and data are don't share the same pages - with the
exception of MIPS16 code which uses address constants embedded between
the code. The following sequence of events may break the code:
o MIPS16 executable being loaded
o dynamic linker relocates the address constants embedded into the code:
o Uses mprotect(2) to make code pages PROT_READ|PROT_WRITE
o Performs the actual relocations by writing to the pages which likely
are COW. Because no PROT_EXEC is set I-cache coherence will not be
considered.
o Uses mprotect(2) to switch code pages back to PROT_READ|PROT_EXEC.
This results in a call to flush_cache_range() which also does not
consider I-caches.
o => executing the page just having been relocated may now result in the
I-cache getting refilled with stale data from memory.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
There are some places left in mips, that lookup task in initial namespace,
while the code doing so gets the pid from the user space and thus must
treat it as virtual.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
ide-cd: fix missing residual count setting in DMA mode
ht6560b: force prefetch for some devices
ht6560b can only do up to PIO mode 4
linux/hdsmart.h: fix goofups (take 2)
via82cxxx: add new PCI id for cx700
falconide: locking bugfix
MAINTAINERS: update ide-cd maintainer's email address
ide/libata: ST310211A has buggy HPA too
ide: Add missing base addresses for falconide and macide
Clearly this was supposed to be an == not an = in the if statement.
This patch also causes us to stop processing execve args once we have
failed rather than continuing to loop on failure over and over and over.
Signed-off-by: Eric Paris <eparis@redhat.com>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes the missing residual count setting in DMA mode,
which was introduced during the conversion to blk-end-request.
The residual count could be used by the request submitter.
So if it isn't set correctly, some upper layers does not work.
(e.g. wodim for CD burning.)
The bug is in only DMA mode.
In PIO mode, we are setting the residual count correctly,
so no need to fix.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Reported-by: Andreas Schwab <schwab@suse.de>
Tested-by: Andreas Schwab <schwab@suse.de>
Tested-by: Laura Garcia <nevola@gmail.com>
Tested-by: Borislav Petkov <petkovbb@googlemail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Prefetch needs to be set for some ide devices to work when connected to
a ht6560b interface. This was not always done properly, causing a system
with a HD and CD on the primary interface to not work properly. Or, in
effect, hang hard.
This patch forces prefetch on devices before checking whether it
is necessary to change the settings in the interface
This patch should also be applied to 2.4. I don't currently have a
2.4 tree around.
(also change my email address)
Signed-off-by: Jan Evert van Grootheest <janevert@caiway.nl>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
According to the datasheet, ht6560b only supports up to PIO mode 4.
[bart: manually ported it over 2.6.25-rc2]
Signed-off-by: Jan Evert van Grootheest <janevert@caiway.nl>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix goofups of commit 76166952bb
("<linux/hdsmart.h> is not used by kernel code").
Also update include/linux/Kbuild to reflect the fact that hdsmart.h
uses __KERNEL__ ifdefs now.
Reported-by: "Robert P. J. Day" <rpjday@crashcourse.ca>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
[bart: manually ported it over via82cxxx changes]
From: Andrew Smith <asmith@tranquility.fsbusiness.co.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
commit 8ac4ce742c ("ide: fix host drivers
depending on ide_generic to probe for interfaces (take 2)") moved probing
to falconide but forgot to take care of Atari specific locking - fix it.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michael Schmitz <schmitz@debian.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
commit 29dd59755a ("ide: remove ide_setup_ports")
forgot to take into account the base addresses for the CONTROL registers for
falconide and macide, as pointed out by Michael Schmitz.
Falconide was tested on Aranym.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michael Schmitz <schmitz@debian.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/nes: Fix possible array overrun
RDMA/nes: Fix VLAN support
RDMA/nes: Fix MAC interrupt erroneously masked on ifdown
IB: Fix return value in ib_device_register_sysfs()
* git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86:
x86: fix lguest build failure
x86: reenable support for system without on node0
x86: CPA: avoid double checking of alias ranges
x86: CPA no alias checking for _NX
x86: zap invalid and unused pmds in early boot
x86: CPA, fix alias checks
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild:
kbuild: explain why DEBUG_SECTION_MISMATCH is UNDEFINED
kbuild: fix building vmlinux.o
kbuild: allow -fstack-protector to take effect
kconfig: fix select in combination with default
drivers/lguest/x86/switcher_32.S:(.text+0x3815f8):
undefined reference to `LGUEST_PAGES_regs_trapnum'
This problem was caused by asm-offsets.c only having the offsets when
lguest *guest* support was set, not lguest host (host support used to
imply guest support, so now they're separate these bugs come out).
Lguest guest support and host support are separate config options:
they used to be tied together. Sort out which parts of asm-offsets are
needed for Guest and Host.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When the CPA code is called with an virtual address in the range of
the direct mapping or the high alias then we do not need to run
through the alias check for this range.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
NX settings are not required to be consistent across alias mappings.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The early boot code maps KERNEL_TEXT_SIZE (currently 40MB) starting
from __START_KERNEL_map. The kernel itself only needs _text to _end
mapped in the high alias. On relocatible kernels the ASM setup code
adjusts the compile time created high mappings to the relocation. This
creates invalid pmd entries for negative offsets:
0xffffffff80000000 -> pmd entry: ffffffffff2001e3
It points outside of the physical address space and is marked present.
This starts at the virtual address __START_KERNEL_map and goes up to
the point where the first valid physical address (0x0) is mapped.
Zap the mappings before _text and after _end right away in early
boot. This removes also the invalid entries.
Furthermore it simplifies the range check for high aliases.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
c_p_a() did not discover all aliases correctly. (such as when called
on vmalloc()-ed areas or ioremap()-ed areas)
Push the alias checks to the lower, physical level and consistently
discover all aliases that might exist: the low direct mappings and
the high linear kernel-text mappings (on 64-bit).
Thanks to Andi Kleen for pointing out that this was buggy.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In nes_create_qp(), the test
if (nesqp->mmap_sq_db_index > NES_MAX_USER_WQ_REGIONS) {
is used to error out if the db_index is too large; however, if the
test doesn't trigger, then the index is used as
nes_ucontext->mmap_nesqp[nesqp->mmap_sq_db_index] = nesqp;
and mmap_nesqp is declared as
struct nes_qp *mmap_nesqp[NES_MAX_USER_WQ_REGIONS];
which leads to an array overrun if the index is exactly equal to
NES_MAX_USER_WQ_REGIONS. Fix this by bailing out if the index is
greater than or equal to NES_MAX_USER_WQ_REGIONS.
This was spotted by the Coverity checker (CID 2162).
Acked-by: Glenn Streiff <gstreiff@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Thanks to Martin Michlmayr <tbm@cyrius.com> for reporting this issue:
The zoran driver fails to compile on the ARM Orion platform with:
In file included from drivers/media/video/zoran_procfs.c:50:
drivers/media/video/zoran.h:232: error: expected identifier before numeric
constant
The reason is that drivers/media/video/zoran.h defines an enum with
GPIO_MAX in it, but Orion contains a #define GPIO_MAX 32 in
include/asm-arm/arch-orion/orion.h
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There was a possible race condition in the increment/decrement of
the active device references counter.
Thanks to Trent Piepho (xyzzy@speakeasy.org) for bringing it up.
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix compilation of user processes which includes videodev*.h but
not includes linux/ioctl.h:
v4l2ext_helper.c: In function 'process_ioctl':
v4l2ext_helper.c:183: warning: implicit declaration of function '_IOWR'
v4l2ext_helper.c:183: error: expected expression before 'struct'
v4l2ext_helper.c:183: error: case label does not reduce to an integer constant
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The initial work to convert the bttv driver to V4L2 "Partial conversion
from V4L1 to V4L2" (e84619b174), missed
the line which set the appropriate overlay crop structure in the newly
allocated bttv_buffer. This then causes a divide error in the
bttv_calc_geo function.
Signed-off-by: Robert Fitzsimons <robfitz@273k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
drivers/built-in.o: In function `set_type':
tuner-core.c:(.text+0x8879d): undefined reference to `xc5000_attach'
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
It currently isn't possible to open the frontend device of cx88-mpeg devices
(DVB or Blackbird) multiple times concurrently. (for instance, to attach a
signal monitoring tool while reading a stream, or to send a frequency change
ioctl) This patch fixes that condition.
Signed-off-by: Roland Stoll <roland@xindex.de>
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Do away with the need to set tuner=63 on cx88xx with recent HVR-1300 boards
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Together with Oliver Neukum from Novell, USB autosuspend support was added.
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch combines all the finished discussions and its resulting patches from
the mailing list.
The version 1.0.6 is mainly influenced by Oliver Neukum. He found a lot of
small issues, that are fixed with this patch now. For me the most interesting
thing is, that it's now safer to use it on other architectures.
The history for version 1.0.6 is:
- fixed coverity checker warnings in *_usb_driver_disconnect
- probe()/open() race by correct ordering in probe()
- DMA coherency rules by separate allocation of all buffers
- use of endianness macros
- abuse of spinlock, replaced by mutex
- racy handling of timer in disconnect, replaced by delayed_work
- racy interruptible_sleep_on(), replaced with wait_event_interruptible()
- handle signals in read()
The driver is tested with all Debian/testing radio programs and rdsd. The patch
is tested against checkpatch.pl v1.12.
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some cards need the diseqc signal modulated, while some just need
the envelope to control the LNB supply.
This fixes Bug 9887
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
fix the following build warning:
radio-si470x.c: In function 'si470x_get_rds_registers':
radio-si470x.c:562: warning: format '%ld' expects type 'long int',
but argument 3 has type 'unsigned int'
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
