Currently, page fault handlers don't issue a mfc restart if the context
switch pending flag is set, which can leave us with a hanging DMA after
a context restore.
This patch introduces fault pending flag that is set by the fault
handler and read by the context switch code, so that the latter can add
the restart bit at the right spot, after it has successfuly saved the
state of the mfc control register.
Signed-off-by: Luke Browning <lukebr@linux.vnet.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
SPU class 0 & 1 exceptions may occur in parallel, so we may end up
overwriting csa.dsisr.
This change adds dedicated fields for each class to the spu and the spu
context so that fault data is not overwritten.
Signed-off-by: Luke Browning <lukebr@linux.vnet.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Currently, we re-route SPU interrupts to the current cpu, which may be
on a remote node. In the case of time slicing, all spu interrupts will
end up routed to the same cpu, where the spusched_tick occurs.
This change routes mfc interrupts to the cpu where the controlling
thread last ran, provided that cpu is on the same node as the spu
(otherwise don't reroute interrupts).
This should improve performance and provide a more predictable
environment for processing spu exceptions. In the past we have seen
concurrent delivery of spu exceptions to two cpus. This eliminates that
concern.
Signed-off-by: Luke Browning <lukebr@linux.vnet.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
synchronize_irq() provides the serialization for
SPU_CONTEXT_SWITCH_PENDING which is read with a simple load. This
routine guarantees that the relevant interrupt handlers are not running,
so that the next time they do run they will see the update
memory value.
This must be done correctly so that exception handling code does not
restart the mfc in the middle of a context switch while we are trying
to atomically stop it and save state.
Signed-off-by: Luke Browning <lukebr@linux.vnet.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
There's currently no way to tell if spu_process_callback has
returned with the state mutex held, as -EINTR may be returned
by either the syscall or the spu_acquire fail case.
Instead, just do a non-interruptible mutex_lock here.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Currently, we update the SPU master run control bit (ie,
spu_enable_spu) in spufs_run_spu before we grab the context mutex. This
can result in races with other processes accessing this context's
resources.
This change moves the spu_enable_spu to after we have acquired the
context lock.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
We currently have two issues with the MFC save code:
* save_mfc_decr doesn't handle a transition of 1 -> 0 of the Ds bit
* The Q bit may be stale in the CSA
This change fixes the first issue by clearing the relevant bits from
the MFC_CNTL value in the CSA before or-ing in the updated status.
Also, we add the Q bit to the updated status.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Currently, we can introduce invalid entries into the MFC queues:
1) context starts a DMA
2) context gets scheduled out during a DMA
- kernel saves MFC queue to CSA
- kernel saves 0x0 in csa->mfc_control_RW
3) context gets scheduled in
- csa->mfc_control[Q] ('queues empty') isn't set, so DMA queues are
restored from the CSA
4) context's DMA is completed
5) context gets scheduled out again, no DMA occuring this time
- kernel sees that MFC_CNTL[Q] ('queues empty') is set, so doesn't
touch saved queue data in CSA
- kernel saves 0x0 in csa->mfc_control_RW
6) context gets scheduled in
- csa->mfc_control[Q] ('queues empty') isn't set (we saved is as 0!),
so DMA queues are restored from the CSA
In this last restore, we've restored the queue status from step 2,
which are now invalid.
This change makes save_mfc_cntl() closer to the save/restore sequence,
as specified in the CBE handbook.
With changes from Luke Browning.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
When we issue a MFC purge request, we may inadvertantly clear the
suspended status.
This change adds the MFC_CNTL_SUSPEND_MASK when we issue a purge
request, so that the suspend bit is masked out.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
We may currently lose interrupts during SPE context switch, as we alter
the INT_Route register. Because the IIC uses a per-thread priority
status, changing the interrupt routing to a different thread means that
the IRQ is no longer masked by the priority status, so we end up with
two fasteoi IRQ handlers executing for the one irq_desc. The fasteoi
handler doesn't handle multiple IRQs, so drops the second one.
Fix this by using our own flow handler. This is based on
handle_edge_irq, but issues an eoi after IRQs are handled, and doesn't
do any mask/unmasking.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
This fixes a regression reported by Kamalesh Bulabel where a POWER4
machine would crash because of an SLB miss at a point where the SLB
miss exception was unrecoverable. This regression is tracked at:
http://bugzilla.kernel.org/show_bug.cgi?id=10082
SLB misses at such points shouldn't happen because the kernel stack is
the only memory accessed other than things in the first segment of the
linear mapping (which is mapped at all times by entry 0 of the SLB).
The context switch code ensures that SLB entry 2 covers the kernel
stack, if it is not already covered by entry 0. None of entries 0
to 2 are ever replaced by the SLB miss handler.
Where this went wrong is that the context switch code assumes it
doesn't have to write to SLB entry 2 if the new kernel stack is in the
same segment as the old kernel stack, since entry 2 should already be
correct. However, when we start up a secondary cpu, it calls
slb_initialize, which doesn't set up entry 2. This is correct for
the boot cpu, where we will be using a stack in the kernel BSS at this
point (i.e. init_thread_union), but not necessarily for secondary
cpus, whose initial stack can be allocated anywhere. This doesn't
cause any immediate problem since the SLB miss handler will just
create an SLB entry somewhere else to cover the initial stack.
In fact it's possible for the cpu to go quite a long time without SLB
entry 2 being valid. Eventually, though, the entry created by the SLB
miss handler will get overwritten by some other entry, and if the next
access to the stack is at an unrecoverable point, we get the crash.
This fixes the problem by making slb_initialize create a suitable
entry for the kernel stack, if we are on a secondary cpu and the stack
isn't covered by SLB entry 0. This requires initializing the
get_paca()->kstack field earlier, so I do that in smp_create_idle
where the current field is initialized. This also abstracts a bit of
the computation that mk_esid_data in slb.c does so that it can be used
in slb_initialize.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Other OS wakeup is not supported from the IR controller,
the bluetooth controller nor the RTC. Remove references
to these in the PS3 sys-manager source.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The routines ps3_virq_setup() and ps3_virq_destroy() are used
in only one file, so make them static.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add an include <asm/time.h> statement for get_tb().
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Arrange for a syntax check to always be done on the powerpc/mm/slb.c
DBG() macro by defining it to pr_debug() for non-debug builds.
Also, fix these related compile warnings:
slb.c:273: warning: format '%04x' expects type 'unsigned int', but argument 2 has type 'long unsigned int
slb.c:274: warning: format '%04x' expects type 'unsigned int', but argument 2 has type 'long unsigned int'
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
arch/powerpc/sysdev/xilinx_intc.c: In function 'xilinx_intc_init':
arch/powerpc/sysdev/xilinx_intc.c:111: warning: format '%08X' expects type 'unsigned int', but argument 2 has type 'resource_size_t'
drivers/char/xilinx_hwicap/xilinx_hwicap.c: In function 'hwicap_setup':
drivers/char/xilinx_hwicap/xilinx_hwicap.c:626: warning: cast to pointer from integer of different size
drivers/char/xilinx_hwicap/xilinx_hwicap.c:646: warning: format '%x' expects type 'unsigned int', but argument 6 has type 'resource_size_t'
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When resource_size_t is larger than an int, the current code
generates a build warning. Kill it.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix current (-git16) missing docbook/kernel-doc notation in RapidIO files.
Warning(linux-2.6.25-git16//include/linux/rio.h:187): No description found for parameter 'sys_size'
Warning(linux-2.6.25-git16//include/linux/rio.h:187): No description found for parameter 'phy_type'
Warning(linux-2.6.25-git16//arch/powerpc/sysdev/fsl_rio.c:188): No description found for parameter 'mport'
Warning(linux-2.6.25-git16//arch/powerpc/sysdev/fsl_rio.c:224): No description found for parameter 'mport'
Warning(linux-2.6.25-git16//arch/powerpc/sysdev/fsl_rio.c:245): No description found for parameter 'mport'
Warning(linux-2.6.25-git16//arch/powerpc/sysdev/fsl_rio.c:270): No description found for parameter 'mport'
Warning(linux-2.6.25-git16//arch/powerpc/sysdev/fsl_rio.c:311): No description found for parameter 'mport'
Warning(linux-2.6.25-git16//arch/powerpc/sysdev/fsl_rio.c:996): No description found for parameter 'dev'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds pcie node which is resposible for PCI-E x8 slot
functioning. Though, this was tested using only x1 SKY2 NIC.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
mpc52xx_uart_int and __uart_put_char both try to acquire the
port->lock. Therefore the function sequence of:
mpc52xx_uart_int--> ...-->flush_to_ldisc-->...-->__uart_put_char
can potentially trigger a deadlock. To avoid this deadlock a fix
similar to that found in the 8250.c serial driver is applied. The
deadlock is avoided by releasing the lock before pushing a buffer
and reacquiring it when completed.
Signed-off-by: Andrew Liu <shengping.liu@windriver.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Various improvements for configuring the MPC5200 MII link from the
device tree:
* Look for 'current-speed' property for fixed speed MII links
* Look for 'fsl,7-wire-mode' property for boards using the 7 wire mode
* move definition of private data structure out of the header file
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Commit edd8ce6743 (Use extended crashkernel
command line on ppc64), changed the logic in reserve_crashkernel()
which deals with the crashkernel= command line option.
This introduced a bug in the case when there is no crashkernel= option,
or it is incorrect. We would fall through and calculate the crash_size
based on the existing values in crashk_res. If both start and end are 0,
the default, we calculate the crash_size as 1 byte - which is wrong.
Rework the logic so that we use crashk_res, regardless of whether it's
set by the command line or via the device tree (see prom.c). Then check
if we have an empty range (end == start), and if so make sure to set
both end and start to zero (this is checked in machine_kexec_64.c). Then
we calculate the crash_size once we know we have a non-zero range.
Finally we always want to warn the user if they specify a base != 32MB,
so remove the special case for that in the command line parsing case.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The current_thread_info() macro, used by preempt_count(), assumes the
base address and size of the stack are THREAD_SIZE aligned.
The emergency stack currently isn't either of these things, which
could potentially cause problems anytime we're running on the
emergency stack. That includes when we detect a bad kernel stack
pointer, and also during early_setup_secondary().
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The sputrace module contained a trace entry for spu_acquire_saved, but
this marker was not placed anywhere. Fix this by adding a marker to the
routine.
Signed-off-by: Julio M. Merino Vidal <jmerino@ac.upc.edu>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Fix a typo in the marker for the find_victim function, which prevented
it from being traced. It previously read find_vitim.
Signed-off-by: Julio M. Merino Vidal <jmerino@ac.upc.edu>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
The sputrace module contained a reference to a marker for
destroy_spu_context, but this marker did not appear in the code. Fix
this by adding a marker in the function.
Signed-off-by: Julio M. Merino Vidal <jmerino@ac.upc.edu>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
The markers facility defines the marker parameters to be of the form
'name %format'. Add parameter names to sputrace, to specify the context
and %spu paramerters, instead of just specifying the '%format' part.
Signed-off-by: Julio M. Merino Vidal <jmerino@ac.upc.edu>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
There are userspace instrumentation tools that need to monitor spu
context switches. This patch adds a new file called 'switch_log' to
each spufs context directory that can be used to monitor the context
switches.
Context switch in/out and exit from spu_run are monitored after the
file was first opened and can be read from it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Board-specific defconfigs based on current mpc5200_defconfig, archival
lite5200_defconfig, and [cm5200|motionpro|tqm5200]_defconfig from the
linux-2.6-denx tree. Kernels build using these defconfigs were verified
to boot with root filesystem mounted over NFS on Motion-PRO, TQM5200
and Lite5200B boards. CM5200 target was not tested due to hardware
unavailability.
Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The error handling for the mpc5200 fec interrupt is broken. The intended
behaviour is like this:
* If one of FEC_IEVENT_RFIFO_ERROR and FEC_IEVENT_XFIFO_ERROR happens,
the datasheet says (MPC5200B User's Guide R1.2, p. 14-13): "When this
occurs, software must ensure both the FIFO Controller and BestComm are
soft-reset".
* On any other error (non-TFINT) interrupt, just issue a debug message.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add board support for the Phytec pcm030 mpc5200b based board. It
does not need any platform specific fixups and as such is handled
as a mpc5200 simple platform.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds gpiolib support for mpc5200 SOCs.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add a set_type function for external (GPIO) interrupts.
Signed-off-by: Juergen Beisert <j.beisert@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
If CONFIG_PPC_MPC5121 is not set, then the of_device_id table for the
mpc5200 serial driver will not get terminated with a NULL entry.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Change RapidIO doorbell source and target ID field to 16-bit for
support large system size, which max rio devid is 65535.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds properties describing the RapidIO controller to the
device-tree source for the MPC8641HPCN board.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The RapidIO system size will auto probe in RIO setup. The route table
and rionet_active in rionet.c are changed to be allocated dynamically
according to the size of the system.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This initializes the RapidIO controller driver using addresses and
interrupt numbers obtained from the firmware device tree, rather than
using hardcoded constants.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The original RapidIO driver suppose there is only one mpc85xx RIO controller
in system. So, some data structures are defined as mpc85xx_rio global, such
as 'regs_win', 'dbell_ring', 'msg_tx_ring'. Now, I changed them to mport's
private members. And you can define multi RIO OF-nodes in dts file for multi
RapidIO controller in one processor, such as PCI/PCI-Ex host controllers in
Freescale's silicon. And the mport operation function declaration should be
changed to know which RapidIO controller is target.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>