Commit Graph

95 Commits

Author SHA1 Message Date
Jay Vosburgh
c2edacf80e bonding / ipv6: no addrconf for slaves separately from master
At present, when a device is enslaved to bonding, if ipv6 is
active then addrconf will be initated on the slave (because it is closed
then opened during the enslavement processing).  This causes DAD and RS
packets to be sent from the slave.  These packets in turn can confuse
switches that perform ipv6 snooping, causing them to incorrectly update
their forwarding tables (if, e.g., the slave being added is an inactve
backup that won't be used right away) and direct traffic away from the
active slave to a backup slave (where the incoming packets will be
dropped).

	This patch alters the behavior so that addrconf will only run on
the master device itself.  I believe this is logically correct, as it
prevents slaves from having an IPv6 identity independent from the
master.  This is consistent with the IPv4 behavior for bonding.

	This is accomplished by (a) having bonding set IFF_SLAVE sooner
in the enslavement processing than currently occurs (before open, not
after), and (b) having ipv6 addrconf ignore UP and CHANGE events on
slave devices.

	The eql driver also uses the IFF_SLAVE flag.  I inspected eql,
and I believe this change is reasonable for its usage of IFF_SLAVE, but
I did not test it.

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-10 12:41:19 -04:00
Jay Vosburgh
031ae4deb0 bonding: Fix 802.3ad no carrier on "no partner found" instance
Modify carrier state determination for 802.3ad mode to comply
with section 43.3.9 of IEEE 802.3, which requires that "Links that are
not successful candidates for aggregation (e.g., links that are attached
to other devices that cannot perform aggregation or links that have been
manually configured to be non-aggregatable) are enabled to operate as
individual IEEE 802.3 links."

	Bug reported by Laurent Chavey <chavey@google.com>.  This patch
is an updated version of his patch that changes the wording of
commentary and adds an update to the driver version.

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Laurent Chavey <chavey@google.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-06-20 19:12:41 -04:00
Jay Vosburgh
3201e656ce bonding: Fix use after free in unregister path
The following patch (based on a patch from Stephen Hemminger
<shemminger@linux-foundation.org>) removes use after free conditions in
the unregister path for the bonding master.  Without this patch, an
operation of the form "echo -bond0 > /sys/class/net/bonding_masters"
would trigger a NULL pointer dereference in sysfs.  I was not able to
induce the failure with the non-sysfs code path, but for consistency I
updated that code as well.

	I also did some testing of the bonding /proc file being open
while the bond is being deleted, and didn't see any problems there.

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-06-20 19:12:41 -04:00
Michael Opdenacker
59c51591a0 Fix occurrences of "the the "
Signed-off-by: Michael Opdenacker <michael@free-electrons.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
2007-05-09 08:57:56 +02:00
Rusty Russell
5a1b5898ee [NET]: Remove NETIF_F_INTERNAL_STATS, default to internal stats.
Herbert Xu conviced me that a new flag was overkill; every driver
currently overrides get_stats, so we might as well make the internal
one the default.  If someone did fail to set get_stats, they would now
get all 0 stats instead of "No statistics available".

Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-28 21:04:03 -07:00
Rusty Russell
c45d286e72 [NET]: Inline net_device_stats
Network drivers which keep stats allocate their own stats structure
then write a get_stats() function to return them.  It would be nice if
this were done by default.

1) Add a new "stats" field to "struct net_device".
2) Add a new feature field to say "this driver uses the internal one"
3) Have a default "get_stats" which returns NULL if that feature not set.
4) Change callers to check result of get_stats call for NULL, not if
   ->get_stats is set.

This should not break backwards compatibility with older drivers, yet
allow modern drivers to shed some boilerplate code.

Lightly tested: works for a modified lguest network driver.

Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:28:26 -07:00
Arnaldo Carvalho de Melo
b0e380b1d8 [SK_BUFF]: unions of just one member don't get anything done, kill them
Renaming skb->h to skb->transport_header, skb->nh to skb->network_header and
skb->mac to skb->mac_header, to match the names of the associated helpers
(skb[_[re]set]_{transport,network,mac}_header).

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:26:20 -07:00
Arnaldo Carvalho de Melo
0660e03f6b [SK_BUFF]: Introduce ipv6_hdr(), remove skb->nh.ipv6h
Now the skb->nh union has just one member, .raw, i.e. it is just like the
skb->mac union, strange, no? I'm just leaving it like that till the transport
layer is done with, when we'll rename skb->mac.raw to skb->mac_header (or
->mac_header_offset?), ditto for ->{h,nh}.

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:25:14 -07:00
Arnaldo Carvalho de Melo
d0a92be05e [SK_BUFF]: Introduce arp_hdr(), remove skb->nh.arph
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:25:12 -07:00
Arnaldo Carvalho de Melo
eddc9ec53b [SK_BUFF]: Introduce ip_hdr(), remove skb->nh.iph
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:25:10 -07:00
Arnaldo Carvalho de Melo
d56f90a7c9 [SK_BUFF]: Introduce skb_network_header()
For the places where we need a pointer to the network header, it is still legal
to touch skb->nh.raw directly if just adding to, subtracting from or setting it
to another layer header.

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:24:59 -07:00
Arnaldo Carvalho de Melo
e7dd65dafd [SK_BUFF] bonding: Set skb->nh.raw relative to skb->mac.raw
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:24:56 -07:00
Arnaldo Carvalho de Melo
a16aeb3623 [BONDING]: Introduce arp_pkt()
For consistency with all the other skb->nh.raw accessors.

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:24:44 -07:00
Arnaldo Carvalho de Melo
459a98ed88 [SK_BUFF]: Introduce skb_reset_mac_header(skb)
For the common, open coded 'skb->mac.raw = skb->data' operation, so that we can
later turn skb->mac.raw into a offset, reducing the size of struct sk_buff in
64bit land while possibly keeping it as a pointer on 32bit.

This one touches just the most simple case, next will handle the slightly more
"complex" cases.

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:24:32 -07:00
Jay Vosburgh
a816c7c712 bonding: Improve IGMP join processing
In active-backup mode, the current bonding code duplicates IGMP
traffic to all slaves, so that switches are up to date in case of a
failover from an active to a backup interface.  If bonding then fails
back to the original active interface, it is likely that the "active
slave" switch's IGMP forwarding for the port will be out of date until
some event occurs to refresh the switch (e.g., a membership query).

	This patch alters the behavior of bonding to no longer flood
IGMP to all ports, and to issue IGMP JOINs to the newly active port at
the time of a failover.  This insures that switches are kept up to date
for all cases.

	"GOELLESCH Niels" <niels.goellesch@eurocontrol.int> originally
reported this problem, and included a patch.  His original patch was
modified by Jay Vosburgh to additionally remove the existing IGMP flood
behavior, use RCU, streamline code paths, fix trailing white space, and
adjust for style.

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-03-06 06:08:11 -05:00
Jay Vosburgh
e245cb71d4 bonding: only receive ARPs for us
The ARP validation code only needs ARPs for the bonding device.

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-03-06 06:08:11 -05:00
Jay Vosburgh
c4f283b1f2 bonding: fix double dev_add_pack
Bonding can erroneously register the same packet_type to receive
ARPs (for use by ARP validation): once at device open time, and once via
sysfs.  Since sysfs can change the validate setting (and thus register
or unregister) at any time, a flag is needed to synchronize with device
open in order to avoid double registrations, and the simplest place is
within the packet_type structure itself.  Double unregister is not an
issue.

	Bug reported by Ulrich Oelmann <ulrich.oelmann@web.de>.

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-03-06 06:08:11 -05:00
Dan Aloni
5c15bdec5c [VLAN]: Avoid a 4-order allocation.
This patch splits the vlan_group struct into a multi-allocated struct. On
x86_64, the size of the original struct is a little more than 32KB, causing
a 4-order allocation, which is prune to problems caused by buddy-system
external fragmentation conditions.

I couldn't just use vmalloc() because vfree() cannot be called in the
softirq context of the RCU callback.

Signed-off-by: Dan Aloni <da-x@monatomic.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-03-02 20:44:51 -08:00
Tim Schmielau
cd354f1ae7 [PATCH] remove many unneeded #includes of sched.h
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there.  Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.

To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.

Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm.  I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).

Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-02-14 08:09:54 -08:00
Arjan van de Ven
d54b1fdb1d [PATCH] mark struct file_operations const 5
Many struct file_operations in the kernel can be "const".  Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data.  In addition it'll catch accidental writes at compile time to
these shared resources.

Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-02-12 09:48:45 -08:00
Joe Jin
243cb4e560 [BONDING]: Replace kmalloc() + memset() pairs with the appropriate kzalloc() calls
Replace kmalloc() + memset() pairs with the appropriate kzalloc() calls in
the bonding driver.

Signed-off-by: Joe Jin <lkmaillist@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2007-02-08 12:38:59 -08:00
Linus Torvalds
f2aca47dc3 Merge master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6: (28 commits)
  sysfs: Shadow directory support
  Driver Core: Increase the default timeout value of the firmware subsystem
  Driver core: allow to delay the uevent at device creation time
  Driver core: add device_type to struct device
  Driver core: add uevent vars for devices of a class
  SYSFS: Fix missing include of list.h in sysfs.h
  HOWTO: Add a reference to Harbison and Steele
  sysfs: error handling in sysfs, fill_read_buffer()
  kobject: kobject_put cleanup
  sysfs: kobject_put cleanup
  sysfs: suppress lockdep warnings
  Driver core: fix race in sysfs between sysfs_remove_file() and read()/write()
  driver core: Change function call order in device_bind_driver().
  driver core: Don't stop probing on ->probe errors.
  driver core fixes: device_register() retval check in platform.c
  driver core fixes: make_class_name() retval checks
  /sys/modules/*/holders
  USB: add the sysfs driver name to all modules
  SERIO: add the sysfs driver name to all modules
  PCI: add the sysfs driver name to all modules
  ...
2007-02-07 19:22:26 -08:00
Greg Kroah-Hartman
43cb76d91e Network: convert network devices to use struct device instead of class_device
This lets the network core have the ability to handle suspend/resume
issues, if it wants to.

Thanks to Frederik Deweerdt <frederik.deweerdt@gmail.com> for the arm
driver fixes.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-07 10:37:11 -08:00
Jay Vosburgh
658f648ad1 bonding: update version
Update version number to reflect recent changes.

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-05 16:58:47 -05:00
Jay Vosburgh
877cbd36b2 bonding: modify sysfs support to permit multiple loads
The existing code would blindly attempt to create the
bonding_masters file (in /sys/class/net) every time the module was
loaded.  When the module is loaded multiple times (which is the
historical method used by initscripts and sysconfig to create multiple
bonding interfaces), this caused load failure of the second module load
attempt, as the creation request would fail.

	This changes the code to note the failure, arrange to not remove
the bonding_masters file upon module exit, and then return success.

	Bonding interfaces created by the second or subsequent loads of
the module will not exist in bonding_masters.  This is not a significant
change, as previously only the interfaces from the most recent load of
the module would be listed.  Both situations are less than optimal, but
this case permits compatibility with existing distro configuration
scripts, and is consistent.

	Note that previously, the sysfs create request would overwrite
the exsting bonding_masters file and succeed, allowing multiple loads of
the module.  The sysfs code has recently changed to return an error if
the file being created already exists.

	Patrick McHardy <kaber@trash.net>, who reported this problem,
observed crashes on the old kernel (before sysfs checked for
duplicates).  I did not experience such crashes, but this change should
resolve them.

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-05 16:58:47 -05:00
Jay Vosburgh
09c8927976 bonding: fix error check in sysfs creation
The existing code did not correctly handle failures to create
the per-interface sysfs group for bonding.

	Modified code to notice errors, and correctly unwind.

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-05 16:58:47 -05:00
Jay Vosburgh
e4b91c4846 bonding: fix device name allocation error
The code to select names for the bonding interfaces was, for the
non-sysfs creation case, always using a hard-coded set of bond0, bond1,
etc, up to max_bonds.  This caused conflicts for the second or
subsequent loads of the module.

	Changed the code to obtain device names from dev_alloc_name().

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-05 16:58:47 -05:00
Adrian Bunk
079ca7da1e bonding.h: "extern inline" -> "static inline"
"extern inline" generates a warning with -Wmissing-prototypes and I'm
currently working on getting the kernel cleaned up for adding this to
the CFLAGS since it will help us to avoid a nasty class of runtime
errors.

If there are places that really need a forced inline, __always_inline
would be the correct solution.

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-05 16:58:47 -05:00
Andy Gospodarek
f8a8ccd56d bonding: ARP monitoring broken on x86_64
While working with the latest bonding code I noticed a nasty problem that
will prevent arp monitoring from always functioning correctly on x86_64
systems.  Comparing ints to longs and expecting reliable results on x86_64
is a bad idea.  With this patch, arp monitoring works correctly again.

Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Stephen Hemminger <shemminger@osdl.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-01-30 09:36:02 -05:00
Andy Gospodarek
4e1400796c [PATCH] bonding: incorrect bonding state reported via ioctl
This is a small fix-up to finish out the work done by Jay Vosburgh to add
carrier-state support for bonding devices.  The output in
/proc/net/bonding/bondX was correct, but when collecting the same info via
an iotcl it could still be incorrect.

Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-12-04 18:36:02 -05:00
Laurent Riffard
418e8f3d7e [PATCH] bonding: fix an oops when slave device does not provide get_stats
Bonding driver unconditionnaly dereference get_stats function pointer
for each of its slave device. This patch
- adds a check for NULL dev->get_stats pointer in bond_get_stats
- prints a notice when the bonding device enslave a device without
  get_stats function.

Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-11-30 06:14:06 -05:00
Peter Zijlstra
0daa230302 [PATCH] bonding: lockdep annotation
=============================================
[ INFO: possible recursive locking detected ]
2.6.17-1.2600.fc6 #1

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-11-10 11:08:52 -05:00
Karsten Keil
39984a9fad [PATCH] bonding: fix deadlock on high loads in bond_alb_monitor()
In bond_alb_monitor the bond->curr_slave_lock write lock is taken
and then dev_set_promiscuity maybe called which can take some time,
depending on the network HW. If a network IRQ for this card come in
the softirq handler maybe try to deliver more packets which end up in
a request to the read lock of bond->curr_slave_lock -> deadlock.
This issue was found by a test lab during network stress tests, this patch
disable the softirq handler for this case and solved the issue.

Signed-off-by: Karsten Keil <kkeil@suse.de>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-10-05 07:01:25 -04:00
Al Viro
a144ea4b7a [IPV4]: annotate struct in_ifaddr
ifa_local, ifa_address, ifa_mask, ifa_broadcast and ifa_anycast are
net-endian.  Annotated them and variables that are inferred to be
net-endian.

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
2006-09-28 18:00:55 -07:00
Jay Vosburgh
0ba8821b12 [PATCH] bonding: update version number
I neglected to properly update the version number in the recent
patch series; this sets it to something reasonable.

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-09-27 16:18:24 -04:00
Jay Vosburgh
8a8e447b2a [PATCH] bonding: Fix primary selection error at enslavement time
At enslavement time, the primary slave might not be activated if
there is already an active slave and the new slave is the primary.
Replaced complicated logic with a call to bond_select_active_slave(),
which does the right thing.

	Fixes http://bugzilla.kernel.org/show_bug.cgi?id=6378

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-09-25 20:08:09 -04:00
Jay Vosburgh
89cc76f95a [PATCH] bonding: Don't mangle LACPDUs
Fixed handling of 802.3ad LACPDUs.  Do not byte swap data in
place in the packet.  Updated nomenclature of "__ntohs_lacpdu" to be
"htons"; it was previously used for both ntohs and htons operations, but
only called ntohs functions.

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-09-25 20:08:09 -04:00
Jay Vosburgh
f5b2b966f0 [PATCH] bonding: Validate probe replies in ARP monitor
Add logic to check ARP request / reply packets used for ARP
monitor link integrity checking.

	The current method simply examines the slave device to see if it
has sent and received traffic; this can be fooled by extraneous traffic.
For example, if multiple hosts running bonding are behind a common
switch, the probe traffic from the multiple instances of bonding will
update the tx/rx times on each other's slave devices.

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-09-25 20:08:09 -04:00
jamal
70298705bb [PATCH] bonding: Don't release slaves when master is admin down
When a bonding netdevice is admin-ed down it loses the slaves
attributes (set via ifenslave). This is not consistent with other
behavior of netdevices (example a qdisc attached to a netdevice doesnt
disappear or an attached IP address etc).
The included patch fixes this. Ive tested by ifenslaving, downing the
bond, checking /proc and making sure it still has the slaves, up-ing the
bond and making sure things continue to work.

Jay/Bonding folks if you are ok with it, just ACK it or include it in
your tree etc. Otherwise we can discuss.

Acked-by: Jay Vosburgh <fubar@us.ibm.com>

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-09-25 20:08:09 -04:00
Jay Vosburgh
0b680e7537 [PATCH] bonding: Add priv_flag to avoid event mishandling
Add priv_flag to specifically identify bonding-involved devices.  Needed
because IFF_MASTER is an unreliable identifier (vlan interfaces above bonding
will inherit IFF_MASTER).  Misidentification of devices would cause
notifier events for other devices to be erroneously processed by bonding,
causing various havoc.

Bug discovered by Martin Papik <martin.papik@ipsec.info>; this patch is
modified from his original.

Signed-off-by: Martin Papik <martin.papik@ipsec.info>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-09-25 20:08:09 -04:00
Jay Vosburgh
54ef313714 [PATCH] bonding: Handle large hard_header_len
The bonding driver fails to adjust its hard_header_len when enslaving
interfaces.  Whenever an interface with a hard_header_len greater than the
ETH_HLEN default is enslaved, the potential for an oops exists, and if the
oops happens while responding to an arp request, for example, the system
panics.  GIANFAR devices may use an extended hard_header for VLAN or
hardware checksumming.  Enslaving such a device and then transmitting over
it causes a kernel panic.

Patch modified from submitter's original, but submitter agreed with this
patch in private email.

Signed-off-by: Mark Huth <mhuth@mvista.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-09-25 20:08:09 -04:00
Jay Vosburgh
a50d8de2cc [PATCH] bonding: Remove unneeded NULL test
Remove unneeded test for NULL.  Reported by Thomas Dillig
<tdillig@stanford.edu> and Isil Dillig <isil@stanford.edu> via Stephen
Hemminger <shemminger@osdl.org>.

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-09-25 20:08:09 -04:00
Kenzo Iwami
65509645ae [PATCH] bonding: Format fix in seq_printf call
Though link_failure_count is type unsigned int, this value is outputted to
/proc/net/bonding/bondX file using "%d" instead of "%u".

The attached patch fixes this problem.

Signed-off-by: Kenzo Iwami <k-iwami@cj.jp.nec.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-09-25 20:08:08 -04:00
Jay Vosburgh
8bb5f96b0c [PATCH] bonding: Convert delay value from s16 to int
The value of "downdelay/miimon" and "updelay/miimon" are stored in
slave->delay. The type of downdelay, updelay, and miimon are all int.
However, slave->delay is type short, and it is not possible to store the
value of "downdelay/miimon" or "updelay/miimon" in some cases. (For example,
miimon=1 downdelay=32768)

The attached patch fixes this problem.

Signed-off-by: Kenzo Iwami <k-iwami@cj.jp.nec.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-09-25 20:08:08 -04:00
Jay Vosburgh
94dbffd540 [PATCH] bonding: Allow bonding to enslave a 10 Gig adapter
Allow channel bonding to enslave a 10 Gig adapter without errors.

Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-09-25 20:08:08 -04:00
Jeff Garzik
7282d491ec drivers/net: const-ify ethtool_ops declarations
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-09-13 14:30:00 -04:00
Jörn Engel
6ab3d5624e Remove obsolete #include <linux/config.h>
Signed-off-by: Jörn Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
2006-06-30 19:25:36 +02:00
Herbert Xu
8648b3053b [NET]: Add NETIF_F_GEN_CSUM and NETIF_F_ALL_CSUM
The current stack treats NETIF_F_HW_CSUM and NETIF_F_NO_CSUM
identically so we test for them in quite a few places.  For the sake
of brevity, I'm adding the macro NETIF_F_GEN_CSUM for these two.  We
also test the disjunct of NETIF_F_IP_CSUM and the other two in various
places, for that purpose I've added NETIF_F_ALL_CSUM.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2006-06-17 22:06:05 -07:00
Herbert Xu
932ff279a4 [NET]: Add netif_tx_lock
Various drivers use xmit_lock internally to synchronise with their
transmission routines.  They do so without setting xmit_lock_owner.
This is fine as long as netpoll is not in use.

With netpoll it is possible for deadlocks to occur if xmit_lock_owner
isn't set.  This is because if a printk occurs while xmit_lock is held
and xmit_lock_owner is not set can cause netpoll to attempt to take
xmit_lock recursively.

While it is possible to resolve this by getting netpoll to use
trylock, it is suboptimal because netpoll's sole objective is to
maximise the chance of getting the printk out on the wire.  So
delaying or dropping the message is to be avoided as much as possible.

So the only alternative is to always set xmit_lock_owner.  The
following patch does this by introducing the netif_tx_lock family of
functions that take care of setting/unsetting xmit_lock_owner.

I renamed xmit_lock to _xmit_lock to indicate that it should not be
used directly.  I didn't provide irq versions of the netif_tx_lock
functions since xmit_lock is meant to be a BH-disabling lock.

This is pretty much a straight text substitution except for a small
bug fix in winbond.  It currently uses
netif_stop_queue/spin_unlock_wait to stop transmission.  This is
unsafe as an IRQ can potentially wake up the queue.  So it is safer to
use netif_tx_disable.

The hamradio bits used spin_lock_irq but it is unnecessary as
xmit_lock must never be taken in an IRQ handler.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2006-06-17 21:30:14 -07:00
Jay Vosburgh
ff59c4563a [PATCH] bonding: support carrier state for master
Add support for the bonding master to specify its carrier state
based upon the state of the slaves.  For 802.3ad, the bond is up if
there is an active, parterned aggregator.  For other modes, the bond is
up if any slaves are up.  Updates driver version to 3.0.3.

	Based on a patch by jamal <hadi@cyberus.ca>.

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-03-29 17:34:02 -05:00