Currently efx_mtd_rename() can race with the probe() and remove()
functions.
Move probe() before device registration and remove() after
unregistration. Move initialisation/update of all names based on the
netdev name into a new function and call it under the RTNL immediately
after registration.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the mtd field is not initialised early enough.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Steve Hodgson <shodgson@solarflare.com>
efx_pci_probe_main() can return success despite a reset being scheduled.
Catch this and retry or abort probe depending on the reset type.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the PHY type names are overly generic. Change them to include
the model numbers of the PHYs they represent.
Correct the model number reference at the top of xfp_phy.c.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool must contend with the MTD driver for the SPI bus lock, which
may carry out long operations such as flash erase. Allow it to be
interrupted while waiting.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our ethtool self-test result names each begin with a component name. For
some results this is "port0", which is not very meaningful. Change that
to "rx" or "phy" as appropriate.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support code for the SFN4111T 100/1000/10GBASE-T reference design,
based in part on the existing code for the SFE4001.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add type codes for the new PHY and rename the SFX7101 type code.
Add definition of clause 22 extension MMD.
Adapt the 10Xpress SFX7101 code to support the SFT9001 as well.
Clean up register definitions.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Steve Hodgson <shodgson@solarflare.com>
MAC, PHY and board events may be separately enabled and signalled.
Our current arrangement of chaining the polling functions can result
in events being missed. Change them to be more independent.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add infrastructure for auto-negotiation of speed, duplex and flow
control.
When using 10Xpress, auto-negotiate flow control. While we're
at it, clean up the code to warn when partner is not 10GBASE-T
capable.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SFC4000 has a separate MAC for use at sub-10G speeds. Introduce
an efx_mac_operations structure with implementations for the two MACs.
Switch between the MACs as necessary.
PHY settings are independent of the MAC, so add get_settings() and
set_settings() to efx_phy_operations. Also add macs field to indicate
which MACs the PHY is connected to.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We often want to set or clear a flag in an MDIO register, but avoid
writing if no change is required since this can have side-effects.
Encapsulate this in a function, mdio_clause45_set_flag().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove kluge for development boards with unspecified board type.
Remove assumption of contiguous board type code assignments.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Combine DEVS0 and DEVS1 registers into a 32-bit mask instead of
reading just DEVS0.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace efx_nic::link_options bitfield with link_speed (speed in
Mbit/s) and link_fd (full duplex flag).
Remove broken auto-negotiation functions.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The loopback self-test checks that IP packets with incorrect checksums
are not altered when sent on a queue with checksum generation off.
These should not contribute to RX error statistics.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change "channel" to "chan".
Shorten PHY loopback names.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate IRQs with the name format <device>[-<type>]-<number> so that
future versions of irqbalanced understand what we're doing.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a bidirectional forwarding test, we find that the best performance
is achieved by sending the TX completion interrupts from one NIC to a
CPU which shares an L2 cache with RX completion interrupts from the
other NIC. To facilitate this, add an option (through a module
parameter) to create separate channels for RX and TX completion with
separate IRQs when MSI-X is available.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is needed for recovery in case a PHY firmware upgrade is aborted.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SFC4000 has strap pins indicating the presence of SPI flash and/or
EEPROM. These pins are also used for GPIO, and in some cases they may
be read wrongly at reset. However, on production boards it must boot
from one or the other device, so we can assume the boot device is
present and read the board config from there.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make falcon_spi_wait() ignore the write timer - it is only relevant to
write commands, it only works for the device that contains VPD, and it
might not be initialised properly at all.
Rename falcon_spi_fast_wait() to falcon_spi_wait_write(), reflecting
its use, and make it wait up to 10 ms (not 1 ms) since buffered writes
to EEPROM may take this long to complete.
Make both wait functions sleep instead of busy-waiting.
Replace wait for command completion at top of falcon_spi_cmd() with a
single poll; no command should be running when the function starts.
Correct some comments.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each reset is serialised by the rtnl_lock anyway, so there's no win
per-NIC.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A value of 0 means indefinite repetition (until interrupted).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was only ever needed for an FPGA version of Falcon.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set dummy monitor method for unrecognised boards.
Clean up board resources if efx_pci_probe_main() fails after board has
been initialised.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: make use of the __iomem address space modifier, and change u_char *,
u_short * and u_int * to void *
Fix more than 30 sparse warnings of this or similar type:
drivers/isdn/hardware/mISDN/hfcmulti.c:261:31: warning: incorrect type in argument 2 (different address spaces)
drivers/isdn/hardware/mISDN/hfcmulti.c:261:31: got unsigned char [usertype] *
drivers/isdn/hardware/mISDN/hfcmulti.c:261:31: expected void volatile [noderef] <asn:2>*addr
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Acked-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix this warning:
drivers/isdn/mISDN/timerdev.c:264:11: warning: incorrect type in initializer (incompatible argument 2 (different address spaces))
drivers/isdn/mISDN/timerdev.c:264:11: expected int ( *read )( ... )
drivers/isdn/mISDN/timerdev.c:264:11: got int ( static [toplevel] *<noident> )( ... )
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Acked-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix this sparse warnings:
drivers/isdn/hardware/mISDN/hfcmulti.c:794: warning: 'vpm_check' defined but not used
drivers/isdn/mISDN/dsp_cmx.c:1546: warning: 'dsp_start_jiffies' defined but not used
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Acked-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: rename function scope variable
Fix this warning:
drivers/isdn/mISDN/l1oip_core.c:472:8: warning: symbol 'id' shadows an earlier one
drivers/isdn/mISDN/l1oip_core.c:254:14: originally declared here
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Acked-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: define first occurence of variable 'nskb' in inner most possible scope
Fix this sparse warning:
drivers/isdn/mISDN/dsp_core.c:746:20: warning: symbol 'nskb' shadows an earlier one
drivers/isdn/mISDN/dsp_core.c:634:19: originally declared here
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Acked-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
'plx_lock' is only used within hfcmulti.c.
Fix this warning:
drivers/isdn/hardware/mISDN/hfcmulti.c:176:1: warning: symbol 'plx_lock' shadows an earlier one
drivers/isdn/hardware/mISDN/hfcmulti.c:175:19: originally declared here
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Acked-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
