Commit Graph

166959 Commits

Author SHA1 Message Date
Stephen Hemminger
ec1b4cf74c net: mark net_proto_ops as const
All usages of structure net_proto_ops should be declared const.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-07 01:10:46 -07:00
Octavian Purdila
f7734fdf61 make TLLAO option for NA packets configurable
On Friday 02 October 2009 20:53:51 you wrote:

> This is good although I would have shortened the name.

Ah, I knew I forgot something :) Here is v4.

tavi

>From 24d96d825b9fa832b22878cc6c990d5711968734 Mon Sep 17 00:00:00 2001
From: Octavian Purdila <opurdila@ixiacom.com>
Date: Fri, 2 Oct 2009 00:51:15 +0300
Subject: [PATCH] ipv6: new sysctl for sending TLLAO with unicast NAs

Neighbor advertisements responding to unicast neighbor solicitations
did not include the target link-layer address option. This patch adds
a new sysctl option (disabled by default) which controls whether this
option should be sent even with unicast NAs.

The need for this arose because certain routers expect the TLLAO in
some situations even as a response to unicast NS packets.

Moreover, RFC 2461 recommends sending this to avoid a race condition
(section 4.4, Target link-layer address)

Signed-off-by: Cosmin Ratiu <cratiu@ixiacom.com>
Signed-off-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-07 01:10:45 -07:00
Brian Haley
51953d5bc4 Use sk_mark for IPv6 routing lookups
Atis Elsts wrote:
> Not sure if there is need to fill the mark from skb in tunnel xmit functions. In any case, it's not done for GRE or IPIP tunnels at the moment.

Ok, I'll just drop that part, I'm not sure what should be done in this case.

> Also, in this patch you are doing that for SIT (v6-in-v4) tunnels only, and not doing it for v4-in-v6 or v6-in-v6 tunnels. Any reason for that?

I just sent that patch out too quickly, here's a better one with the updates.

Add support for IPv6 route lookups using sk_mark.

Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-07 01:10:45 -07:00
Ben Hutchings
d73d3a8cb4 ethtool: Add reset operation
After updating firmware stored in flash, users may wish to reset the
relevant hardware and start the new firmware immediately.  This should
not be completely automatic as it may be disruptive.

A selective reset may also be useful for debugging or diagnostics.

This adds a separate reset operation which takes flags indicating the
components to be reset.  Drivers are allowed to reset only a subset of
those requested, and must indicate the actual subset.  This allows the
use of generic component masks and some future expansion.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-07 01:10:44 -07:00
Eric Dumazet
d250a5f90e pkt_sched: gen_estimator: Dont report fake rate estimators
Jarek Poplawski a écrit :
>
>
> Hmm... So you made me to do some "real" work here, and guess what?:
> there is one serious checkpatch warning! ;-) Plus, this new parameter
> should be added to the function description. Otherwise:
> Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
>
> Thanks,
> Jarek P.
>
> PS: I guess full "Don't" would show we really mean it...

Okay :) Here is the last round, before the night !

Thanks again

[RFC] pkt_sched: gen_estimator: Don't report fake rate estimators

We currently send TCA_STATS_RATE_EST elements to netlink users, even if no estimator
is running.

# tc -s -d qdisc
qdisc pfifo_fast 0: dev eth0 root bands 3 priomap  1 2 2 2 1 2 0 0 1 1 1 1 1 1 1 1
 Sent 112833764978 bytes 1495081739 pkt (dropped 0, overlimits 0 requeues 0)
 rate 0bit 0pps backlog 0b 0p requeues 0

User has no way to tell if the "rate 0bit 0pps" is a real estimation, or a fake
one (because no estimator is active)

After this patch, tc command output is :
$ tc -s -d qdisc
qdisc pfifo_fast 0: dev eth0 root bands 3 priomap  1 2 2 2 1 2 0 0 1 1 1 1 1 1 1 1
 Sent 561075 bytes 1196 pkt (dropped 0, overlimits 0 requeues 0)
 backlog 0b 0p requeues 0

We add a parameter to gnet_stats_copy_rate_est() function so that
it can use gen_estimator_active(bstats, r), as suggested by Jarek.

This parameter can be NULL if check is not necessary, (htb for
example has a mandatory rate estimator)

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-07 01:07:42 -07:00
Tilman Schmidt
92d326f61b net/ppp: fix comments - ppp_{sync,asynctty}_receive() may sleep
The receive_buf methods of the N_PPP and N_SYNC_PPP line disciplines,
ppp_asynctty_receive() and ppp_sync_receive(), call tty_unthrottle()
which may sleep. Fix the comments claiming otherwise.

Impact: documentation
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-07 01:07:41 -07:00
Jiri Pirko
a549952ad3 bonding: introduce primary_reselect option
In some cases there is not desirable to switch back to primary interface when
it's link recovers and rather stay with currently active one. We need to avoid
packetloss as much as we can in some cases. This is solved by introducing
primary_reselect option. Note that enslaved primary slave is set as current
active no matter what.

Patch modified by Jay Vosburgh as follows: fixed bug in action
after change of option setting via sysfs, revised the documentation
update, and bumped the bonding version number.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-07 01:07:39 -07:00
Eric Dumazet
2d37a186ce Use sk_mark for routing lookup in more places
Here is a followup on this area, thanks.

[RFC] af_packet: fill skb->mark at xmit

skb->mark may be used by classifiers, so fill it in case user
set a SO_MARK option on socket.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-07 01:07:38 -07:00
YOSHIFUJI Hideaki / 吉藤英明
fa857afcf7 ipv6 sit: 6rd (IPv6 Rapid Deployment) Support.
IPv6 Rapid Deployment (6rd; draft-ietf-softwire-ipv6-6rd) builds upon
mechanisms of 6to4 (RFC3056) to enable a service provider to rapidly
deploy IPv6 unicast service to IPv4 sites to which it provides
customer premise equipment.  Like 6to4, it utilizes stateless IPv6 in
IPv4 encapsulation in order to transit IPv4-only network
infrastructure.  Unlike 6to4, a 6rd service provider uses an IPv6
prefix of its own in place of the fixed 6to4 prefix.

With this option enabled, the SIT driver offers 6rd functionality by
providing additional ioctl API to configure the IPv6 Prefix for in
stead of static 2002::/16 for 6to4.

Original patch was done by Alexandre Cassen <acassen@freebox.fr>
based on old Internet-Draft.

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-07 01:07:37 -07:00
Ilia K
ee5e81f000 add vif using local interface index instead of IP
When routing daemon wants to enable forwarding of multicast traffic it
performs something like:

       struct vifctl vc = {
               .vifc_vifi  = 1,
               .vifc_flags = 0,
               .vifc_threshold = 1,
               .vifc_rate_limit = 0,
               .vifc_lcl_addr = ip, /* <--- ip address of physical
interface, e.g. eth0 */
               .vifc_rmt_addr.s_addr = htonl(INADDR_ANY),
         };
       setsockopt(fd, IPPROTO_IP, MRT_ADD_VIF, &vc, sizeof(vc));

This leads (in the kernel) to calling  vif_add() function call which
search the (physical) device using assigned IP address:
       dev = ip_dev_find(net, vifc->vifc_lcl_addr.s_addr);

The current API (struct vifctl) does not allow to specify an
interface other way than using it's IP, and if there are more than a
single interface with specified IP only the first one will be found.

The attached patch (against 2.6.30.4) allows to specify an interface
by its index, instead of IP address:

       struct vifctl vc = {
               .vifc_vifi  = 1,
               .vifc_flags = VIFF_USE_IFINDEX,   /* NEW */
               .vifc_threshold = 1,
               .vifc_rate_limit = 0,
               .vifc_lcl_ifindex = if_nametoindex("eth0"),   /* NEW */
               .vifc_rmt_addr.s_addr = htonl(INADDR_ANY),
         };
       setsockopt(fd, IPPROTO_IP, MRT_ADD_VIF, &vc, sizeof(vc));

Signed-off-by: Ilia K. <mail4ilia@gmail.com>

=== modified file 'include/linux/mroute.h'
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-07 00:48:41 -07:00
Tilman Schmidt
7bb5fdc2fb gigaset: add Kernel CAPI interface (v3)
Add a Kernel CAPI interface to the Gigaset driver.

Impact: optional new functionality
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06 22:43:53 -07:00
Tilman Schmidt
aaba2b3f82 gigaset: allow building without I4L
Add a dummy LL interface to the Gigaset driver so that it can be
built and, in a limited way, used without the ISDN4Linux subsystem.

Impact: new configuration alternative
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06 22:43:51 -07:00
Tilman Schmidt
088ec0cc96 gigaset: prepare for CAPI implementation
Reorganize the code of the Gigaset driver, moving all isdn4linux
dependencies to the source file i4l.c so that it can be replaced
by a file capi.c interfacing to Kernel CAPI instead.

Impact: refactoring, no functional change
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06 22:43:50 -07:00
David S. Miller
7ecc59c1b7 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 2009-10-06 22:43:16 -07:00
Tilman Schmidt
1cec9727fb gigaset: add kerneldoc comments
Add kerneldoc comments to some functions in the Gigaset driver.

Impact: documentation
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06 22:21:07 -07:00
Tilman Schmidt
cd7f50e251 gigaset: correct debugging output selection
Dump payload data consistently only when DEBUG_STREAM_DUMP debug bit
is set.

Impact: debugging aid
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06 22:21:06 -07:00
Tilman Schmidt
b5f581d55f gigaset: improve error recovery
When the Gigaset base stops responding, try resetting the USB
connection to recover.

Impact: error handling improvement
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06 22:21:05 -07:00
Tilman Schmidt
05eae94f2a gigaset: fix device ERROR response handling
Clear out pending command that got rejected with 'ERROR' response.
This fixes the bug where unloading the driver module would hang
with the message: "gigaset: not searching scheduled commands: busy"
after a device communication error.

Impact: error handling bugfix
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06 22:21:01 -07:00
Tilman Schmidt
2038724cc7 gigaset: announce if built with debugging
Mention in the driver load announcement whether the driver was built
with debugging messages enabled, to facilitate support.

Impact: informational message
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06 22:21:00 -07:00
Tilman Schmidt
eb4459ff3a gigaset: handle isoc frame errors more gracefully
Don't drop the remainder of an URB if an isochronous frame has an error.

Impact: error handling improvement
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06 22:20:59 -07:00
Tilman Schmidt
ee239d9901 gigaset: linearize skb
The code of the Gigaset driver assumes that sk_buff-s coming
from the ISDN4Linux subsystem are always linear. Explicitly
calling skb_linearize() is cheap if they are, but much more
robust in case they ever aren't.

Impact: robustness improvement
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06 22:20:58 -07:00
Tilman Schmidt
3305adffc5 gigaset: fix reject/hangup handling
Signal D channel disconnect in a few cases where it was missed,
including when an incoming call is disconnected before it was
accepted.

Impact: error handling improvement
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06 22:20:57 -07:00
Tilman Schmidt
9803f79695 isdn: make capidrv module parameter "debugmode" writeable
Being able to change the debugmode module parameter of capidrv on the
fly is quite useful for debugging and doesn't do any harm.

Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06 22:20:55 -07:00
Tilman Schmidt
e48470217d isdn: avoid races in capidrv
In several places, capidrv sends a CAPI message to the ISDN
device and then updates its internal state accordingly.
If the response message from the device arrives before the
state is updated, it may be rejected or processed incorrectly.
Avoid these races by updating the state before emitting the
message.

Impact: bugfix
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Acked-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06 22:20:53 -07:00
Tilman Schmidt
812d73473a isdn: accept CAPI Informational Info values as success
Info values in the 0x00xx range are defined in the CAPI standard
as "Informational, message processed successfully". Therefore a
CONNECT_B3_CONF message with an Info value in that range should
open an NCCI just as with Info==0.

Impact: minor bugfix
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Acked-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06 22:20:52 -07:00
Tilman Schmidt
f1af9f5854 Documentation: expand isdn/INTERFACE.CAPI document
- Note that send_message() may be called in interrupt context.
- Describe the storage of CAPI messages and payload data in SKBs.
- Add more details to the description of the _cmsg structure.
- Describe kernelcapi debugging output.

Impact: documentation
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06 22:20:51 -07:00
Ajit Khaparde
583e3f34eb be2net: Bug fix to properly update ethtool tx-checksumming after ethtool -K <ifname> tx off
This is a fix for a bug which was a result of wrong use of checksum offload flag.
The status of tx-checksumming was not changed from on to off
after a 'ethtool -K <ifname> tx off' operation.
Use the proper checksum offload flag NETIF_F_HW_CSUM instead of
NETIF_F_IP_CSUM and NETIF_F_IPV6_CSUM.
Patch is against net-2.6 tree.

Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06 17:33:41 -07:00
Ajit Khaparde
49643848f9 be2net: Fix a typo in be_cmds.h
MCC_STATUS_NOT_SUPPORTED should be decimal 66 not hex 66.
This patch fixes this typo. Patch against net-2.6 tree.

Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06 17:33:39 -07:00
Ajit Khaparde
c5b9b92e07 be2net: Bug Fix while accounting of multicast frames during netdev stats update
While updating the statistics to be passed via the get_stats,
tx multicast frames were being accounted instead of rx multicast frames.
This patch fixes the bug. This patch is against the net-2.6 tree.

Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06 17:33:38 -07:00
Ron Mercer
86aaf9ad82 qlge: Fix lock/mutex warnings.
Get rid of spinlock and private mutex usage for exclusive access to the
HW semaphore register.  rtnl_lock already creates exclusive access to
this register in all driver API.
Add rtnl to firmware worker threads that also use the HW semaphore register.

Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06 17:33:37 -07:00
Ron Mercer
5ee22a5aa9 qlge: Fix queueing of firmware handler in ISR.
Check that we are not already polling firmware events before we queue the
firmware event worker, then disable firmware interrupts.
Otherwise we can queue the same event multiple times.

Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06 17:33:36 -07:00
Ron Mercer
d799bbfbe2 qlge: Fix some bit definitions for reset register.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06 17:33:35 -07:00
Eric Dumazet
bcdce7195e net: speedup sk_wake_async()
An incoming datagram must bring into cpu cache *lot* of cache lines,
in particular : (other parts omitted (hash chains, ip route cache...))

On 32bit arches :

offsetof(struct sock, sk_rcvbuf)       =0x30    (read)
offsetof(struct sock, sk_lock)         =0x34   (rw)

offsetof(struct sock, sk_sleep)        =0x50 (read)
offsetof(struct sock, sk_rmem_alloc)   =0x64   (rw)
offsetof(struct sock, sk_receive_queue)=0x74   (rw)

offsetof(struct sock, sk_forward_alloc)=0x98   (rw)

offsetof(struct sock, sk_callback_lock)=0xcc    (rw)
offsetof(struct sock, sk_drops)        =0xd8 (read if we add dropcount support, rw if frame dropped)
offsetof(struct sock, sk_filter)       =0xf8    (read)

offsetof(struct sock, sk_socket)       =0x138 (read)

offsetof(struct sock, sk_data_ready)   =0x15c   (read)


We can avoid sk->sk_socket and socket->fasync_list referencing on sockets
with no fasync() structures. (socket->fasync_list ptr is probably already in cache
because it shares a cache line with socket->wait, ie location pointed by sk->sk_sleep)

This avoids one cache line load per incoming packet for common cases (no fasync())

We can leave (or even move in a future patch) sk->sk_socket in a cold location

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06 17:28:29 -07:00
Sreenivasa Honnur
bd32cafc47 vxge: Version update.
- Version Update.

Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06 15:22:55 -07:00
Sreenivasa Honnur
eb5f10c21b vxge: Allow multiple functions with INTA.
- Allow multiple functions with INTA.
- Removed the condition to allow only one vpath with INTA
- Ensure that the alarm bit in titan_mask_all_int register is cleared when
  driver exits.

Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06 15:22:55 -07:00
Sreenivasa Honnur
fa41fd1003 vxge: Check if FCS stripping is disabled by the firmware.
- Added a function to check if FCS stripping is disabled by the firmware, if
  it is not disabled fail driver load.

- By default FCS stripping is disabled by the firmware. With this assumption
  driver decrements the indicated packet length by 4 bytes(FCS length).

- This patch ensures that FCS stripping is disabled during driver load time.

Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06 15:22:54 -07:00
Sreenivasa Honnur
f0dfebafcc vxge: Removed unused functions.
- Removed the wrr_rebalance function

- This feature is not supported by the ASIC, hence removing the related code.

Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06 15:22:53 -07:00
Sreenivasa Honnur
a4a987d822 vxge: Fixed crash in PAE system due to wrong typecasting.
- Fix a crash in PAE system due to wrong typecasting.

- On PAE system size_t is unsigned int which is 32bit. Avoid casting
  64 bit address to 32 bit

Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06 15:22:52 -07:00
Sreenivasa Honnur
0f8f7d58eb vxge: Removed accessing non-supported registers.
- Removed accessing GENDMA_INT register
 - This allowed the firmware to perform a generic DMA write to host memory.
   This feature is not supported by the ASIC, this patch removes access to
   GENDMA_INT register.

Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06 15:22:52 -07:00
Sreenivasa Honnur
657205bdd7 vxge: Update driver_config->vpath_per_dev for each function in probe.
- Update driver_config->vpath_per_dev for each function in probe.

- vpath_per_device specifies number of vpaths supported for each function/device. The
  current code was updating vpath_per_device only for physical device, however this has
  to be updated for each function also in case of a MF(Multi function) device.

Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06 15:22:51 -07:00
Sreenivasa Honnur
92cdd7c377 vxge: Modify __vxge_hw_device_is_privilaged() to not assume function-0 as the privileged function: Resubmit#1
- vxge driver was assuming function-0 is always the privilaged function. Now that
  restriction has been removed any function can act as a privilaged function.

- This patch modifies the __vxge_hw_device_is_privilaged routine to not assume
  function-0 as the privileged function.

- Recreated the patch by incorporating review comments from Dave Miller to
  remove double slash in path names.

Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06 15:22:51 -07:00
Alexander Duyck
6deac6f2b4 igb: add flushes between RAR writes when setting mac address
There are some switches that will do write combining when they see two
sequential regions written. In order to avoid any possible write combining
issues it is necessary to add a flush after writing each piece of a rar
register.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06 14:59:24 -07:00
Alexander Duyck
2553bb2681 igb: add additional error handling to the phy code
This update adds additional exception handling to the phy code to handle
situations where it may be called incorrectly.  In addition it adds some
bounds checking to the cable length checks to prevent an array overrun in
the event that the hardware returned a different value than expected.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06 14:59:24 -07:00
Alexander Duyck
ab576389b7 igb: add code to retry a phy read in the event of failure on link check
This patch adds a retry to phy reads in the event of failure.  The original
code broke out of the loop on failure and this is a mistake as we should be
trying to do the read twice.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06 14:59:23 -07:00
Alexander Duyck
81fadd81a5 igb: move the generic copper link setup code into e1000_phy.c
This patch moves the generic portion of the copper link setup into a
seperate function in e1000_phy.c.  This helps to reduce the size of
copper_link_setup_82575 and make it a bit more readable.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06 14:59:23 -07:00
Alexander Duyck
285b416745 igb: remove microwire support from igb
igb doesn't have any devices that use a microwire interface for NVM.  As
such the code related to this can be removed.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06 14:59:22 -07:00
Alexander Duyck
22896639af igb: change how we handle alternate mac addresses
This patch allows us to treat the alternate mac address as though it is the
physical address on the adapter.  This is accomplished by letting the
alt_mac_address function to only fail on an NVM error.  If no errors occur
and the alternate mac address is not present then RAR0 is read as the
default mac address.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06 14:59:21 -07:00
Alexander Duyck
3272686c98 igb: fix a few items where weren't correctly setup for mbx timeout
The mailbox timeout routines need to be updated as they were not correctly
handling the case of a mailbox timeout and could cause issues with long
delays when used.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06 14:59:21 -07:00
Alexander Duyck
0acb6fde5f igb: add function to handle mailbox lock
Both the read and write mailbox functions need to acquire the mailbox lock.
Since that is the case we might as well combine both of the procedures into
one function so it is easier to maintain.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06 14:59:20 -07:00
Alexander Duyck
747d49baaf igb: add support for 82576NS SerDes adapter
This patch adds the device ID necessary to support the 82576NS SerDes
adapter.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-06 14:59:19 -07:00