We *really* don't want to be reading MFGPTx_SETUP and writing back those
values. What we want to be doing is clearing CMP1 and CMP2 unconditionally;
otherwise, we have races where CMP1 and/or CMP2 fire after we've read
MFGPTx_SETUP. They can also fire between when we've written ~CNTEN to
the register, and when the new register values get copied to the timer's
version of the register. By clearing both fields, we're okay.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
There isn't much value to always detecting the MFGPT timers on
Geode platforms; detection is only needed when something wants
to use the timers. Move the detection code so that it gets
called the first time a timer is allocated.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We need to be called from elsewhere, and this gets some #ifdefs out
of the .c file.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Drop F_AVAIL and the 'flags' field, replacing with an 'avail' bit. This
looks more understandable to me.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We had planned to use the 'owner' field for allowing re-allocation of
MFGPTs; however, doing it by module owner name isn't flexible enough. So,
drop this for now. If it turns out that we need timers in modules, we'll
need to come up with a scheme that matches the write-once fields of the
MFGPTx_SETUP register, and drops ponies from the sky.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The GEODE MFGPT code assumed that 32kHz was 32000 Hz while the boards
run on a 32.768 kHz digital watch crystal. In practise, it will not
change the timer's frequency as the skew was only 2.4%, but it
should provide more accurate intervals.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
- uninline timer functions; the compiler knows better than we do
whether or not to inline these.
- mfgpt_start_timer() had an unused 'clock' argument, drop it.
From both Jordan and myself.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild:
Kbuild: Fix deb-pkg target to work with kernel versions ending with -<text-without-digit>
ide: introduce HAVE_IDE
kbuild: silence CHK/UPD messages according to $(quiet)
scsi: fix makefile for aic7(3*x)
kbuild/modpost: Use warn() for announcing section mismatches
Add binoffset to gitignore
kbuild/modpost: improve warnings if symbol is unknown
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
mmc: extend ricoh_mmc to support Ricoh RL5c476
at91_mci: use generic GPIO calls
sdhci: add num index for multi controllers case
MAINTAINERS: remove non-existant URLs
mmc: remove sdhci and mmc_spi experimental markers
mmc: Handle suspend/resume in Ricoh MMC disabler
Sony MemoryStick cards are used in many products manufactured by Sony.
They are available both as storage and as IO expansion cards. Currently,
only MemoryStick Pro storage cards are supported via TI FlashMedia
MemoryStick interface.
[mboton@gmail.com: biuld fix]
[akpm@linux-foundation.org: build fix]
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Miguel Boton <mboton@gmail.co>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
CC init/main.o
In file included from include2/asm/uaccess.h:8,
from include/linux/poll.h:13,
from include/linux/rtc.h:113,
from include/linux/efi.h:19,
from linux-2.6/init/main.c:43:
include/linux/mm.h:1151:
error: expected declaration specifiers or '...' before 'pgtable_t'
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Reported-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The pte_fn_t in include/linux/mm.h make it necessary for all architectures
to define a pgtable_t type, even those that do not have an mmu.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mm_cgroup() is exclusively used to test whether an mm's mem_cgroup pointer
is pointing to a specific cgroup. Instead of returning the pointer, we can
just do the test itself in a new macro:
vm_match_cgroup(mm, cgroup)
returns non-zero if the mm's mem_cgroup points to cgroup. Otherwise it
returns zero.
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
/home/bunk/linux/kernel-2.6/git/linux-2.6/fs/hostfs/hostfs_kern.c: In function 'hostfs_show_options':
/home/bunk/linux/kernel-2.6/git/linux-2.6/fs/hostfs/hostfs_kern.c:328: error: dereferencing pointer to incomplete type
We need to include mount.h to get vfsmount.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Reported-by: Adrian Bunk <bunk@stusta.de>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
CC mm/vmscan.o
In file included from
/home/bunk/linux/kernel-2.6/git/linux-2.6/mm/vmscan.c:44:
/home/bunk/linux/kernel-2.6/git/linux-2.6/include/linux/swapops.h: In function 'is_swap_pte':
/home/bunk/linux/kernel-2.6/git/linux-2.6/include/linux/swapops.h:48: error: implicit declaration of function 'pte_none'
/home/bunk/linux/kernel-2.6/git/linux-2.6/include/linux/swapops.h:48: error: implicit declaration of function 'pte_present'
Does it ever make sense to ask "is this pte a swap entry?" on a machine
with no MMU? Presumably this also means it has no ptes too, right? In
which case, it's better to comment the whole function out. Then when
someone tries to ask the above meaningless question, they get a compile
error rather than a meaningless answer.
Signed-off-by: Matt Mackall <mpm@selenic.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Reported-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for different number of page table levels dependent
on the highest address used for a process. This will cause a 31 bit
process to use a two level page table instead of the four level page
table that is the default after the pud has been introduced. Likewise
a normal 64 bit process will use three levels instead of four. Only
if a process runs out of the 4 tera bytes which can be addressed with
a three level page table the fourth level is dynamically added. Then
the process can use up to 8 peta byte.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
There are two problems in the vt220 intialization:
o Currently the vt220 console looses early printk events until the
the vt220 tty is registered.
o console should work if tty_register fails
sclp_vt220_con_init calls __sclp_vt220_init and register_console.
It does not register the driver with the sclp core code via
sclp_register. That results in an sclp_send_mask=0. Therefore,
__sclp_vt220_emit will reject buffers with EIO. Unfortunately
register_console will cause the printk buffer to be sent to the
console and, therefore, every early message gets dropped. The
sclp_send_mask is set later during boot, when sclp_vt220_tty_init
calls sclp_register.
The solution is to move the sclp_register call from sclp_vt220_tty_init
to __sclp_vt220_init. This makes sure that the console is properly
registered with the sclp subsystem before the first log buffer messages
are passed to the vt220 console.
We also adopt the cleanup on error to keep the console alive if
tty_register fails.
Thanks to Peter Oberparleiter and Heiko Carstens for review and ideas
for improvement.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If qdio establish runs in parallel with a channel error,
ccw_device_start_timeout may not trigger the qdio_timeout_handler.
In this case neither QDIO_IRQ_STATE_ESTABLISHED nor
QDIO_IRQ_STATE_ERR is reached and the following wait_event hangs
forever.
Solution: do not make use of the timeout option with
ccw_device_start, but add a timeout to the following wait_event.
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
With the new space saving spinlock_t and a non-debug configuration
the struct page only has 32 bytes for 31 bit s390. The causes an
overflow in the calculation of VMEM_MAX_PHYS which renders the
kernel unbootable.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Do not start ap poll thread per default to increase perfomance with
z/VM.
Signed-off-by: Felix Beck <felix.beck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The black art of inline assemblies.. The new __ffs_word_loop/
__ffz_word_loop inline assemblies need an early clobber for the
two input/output variables.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If CONIFIG_LOCALVERSION is set for example to -loop, the following error
message was generated.
dpkg-deb - error: Debian revision (`loop') doesn't contain any digits
dpkg-deb: 1 errors in control file
The patch solves this by adding a numeric revision to package version.
Signed-off-by: Michal Sojka <sojkam1@fel.cvut.cz>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
To allow flexible configuration of IDE introduce HAVE_IDE.
All archs except arm, um and s390 unconditionally select it.
For arm the actual configuration determine if IDE is supported.
This is a step towards introducing drivers/Kconfig for arm.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Russell King - ARM Linux <linux@arm.linux.org.uk>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix bug introduced by my latest fix to the aic7xxx Makefile.
Test build on x86 32 and 64 bit.
Without and with -j (parallel build)
Building firmaware is br0ken with O=... but this
is unrelated to this bug-fix.
Tested-by: Adrian Bunk <bunk@kernel.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
modpost: Use warn() for announcing section mismatches, for easy grepping for
warnings in build logs.
Also change an existing call from fprintf() to warn() while we're at it.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
If we cannot determine the symbol then print
(unknown) to hint the reader that we failed to
find the symbol.
This happens with REL relocation records
in arm object files.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Add some initial documentation detailing what acer-wmi is, and how to use
it. Update the Kconfig entry with a reference to the documentation.
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Also update references to sonypi.txt in Kconfig.
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
CC: Mattia Dongili <malattia@linux.it>
Signed-off-by: Len Brown <len.brown@intel.com>
Also update references to sony-laptop.txt in Kconfig.
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
CC: Mattia Dongili <malattia@linux.it>
Signed-off-by: Len Brown <len.brown@intel.com>
Also update references to thinkpad-acpi.txt in Kconfig.
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
CC: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
There are currently various laptop drivers floating about with no central
place for their documentation, which is currently scattered around the top
level Documentation/ directory.
So, as a first step, lets create a Documentation sub-directory, and update
the relevant index files. The work of then moving the existing laptop
driver related documentation will then be handled later.
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
CC: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
CC: Mattia Dongili <malattia@linux.it>
Signed-off-by: Len Brown <len.brown@intel.com>
This fixes the build, but acpi_fan_add() still needs
to be updated to handle thermal_cooling_device_register()
returning NULL as a non-fatal condition.
Signed-off-by: Len Brown <len.brown@intel.com>
The last posted version of this patch gave compile error
on IA64. So, here goes yet another rewrite of the patch.
Convert cpu_idle_wait() to cpuidle_kick_cpus() which is
SMP-only, and gives error on non supported CPU.
Changes from last patch sent by Kevin:
Moved the definition of kick_cpus back to cpuidle.c from cpuidle.h:
* Having it in .h gives #error on archs which includes the header file without
actually having CPU_IDLE configured. To make it work in .h, we need one more
#ifdef around that code which makes it messy.
* Also, the function is only called from one file. So, it can be in declared
statically in .c rather than making it available to everyone who includes
the .h file.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Len Brown <len.brown@intel.com>
There is some leftover cruft from the old quirk infrastructure that causes
us to be unable to set the backlight on older laptops.
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: Len Brown <len.brown@intel.com>
tc1100-wmi has not undergone as much testing as acer-wmi, so it certainly
should be marked as experimental as well until we get more user feedback.
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: Len Brown <len.brown@intel.com>
