Unlike their older siblings, ICH6 and 7 use different scheme for MAP
VALUE. This patch makes ata_piix interpret MV properly on ICH6/7.
Pre-ICH6/7
The value of these bits indicate the address range the SATA port
responds to, and whether or not the SATA and IDE functions are
combined.
000 = Non-combined. P0 is primary master. P1 is secondary master.
001 = Non-combined. P0 is secondary master. P1 is primary master.
100 = Combined. P0 is primary master. P1 is primary slave. P-ATA is
2:0 Map Value secondary.
101 = Combined. P0 is primary slave. P1 is primary master. P-ATA is
secondary.
110 = Combined. P-ATA is primary. P0 is secondary master. P1 is
secondary slave.
111 = Combined. P-ATA is primary. P0 is secondary slave. P1 is
secondary master.
ICH6/7
Map Value - R/W. Map Value (MV): The value in the bits below indicate
the address range the SATA ports responds to, and whether or not the
PATA and SATA functions are combined. When in combined mode, the AHCI
memory space is not available and AHCI may not be used.
00 = Non-combined. P0 is primary master, P2 is the primary slave. P1
is secondary master, P3 is the 1:0 secondary slave (desktop
only). P0 is primary master, P2 is the primary slave (mobile
only).
01 = Combined. IDE is primary. P1 is secondary master, P3 is the
secondary slave. (desktop only)
10 = Combined. P0 is primary master. P2 is primary slave. IDE is secondary
11 = Reserved
Signed-off-by: Tejun Heo <htejun@gmail.com>
--
Jeff, without this patch, ata_piix misdetects my ICH7's combined mode,
ending up not applying bridge limits to PX-710SA and configuring IDE
drive on 40-c cable to UDMA/66.
Thanks.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
a page while we are still submitting other buffers on the same page for
I/O.
SGI-PV: 948197
SGI-Modid: xfs-linux-melb:xfs-kern:25004a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Nathan Scott <nathans@sgi.com>
sparse can't parse a struct definition in include/asm-powerpc/lppaca.h,
even though gcc can accept it. The form looks like this:
struct __attribute__((whatever)) foo { };
An equivalent that both gcc and sparse can handle is
struct foo { } __attribute__((whatever));
This is the only definition of this type in the tree, and fixing it is
easier than fixing sparse.
Signed-off-by: Bryan O'Sullivan <bos@serpentine.com>
[ Side note: fixing sparse wouldn't be hard, but the "attribute at the
end" version is the canonical one, and the one that makes sense. So
let's just fix the kernel instead. Luc Van Oostenryck already sent
out a sparse patch to the sparse mailing list in case anybody cares.
-- Linus ]
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There are a couple of problems in the DMA setup code for skge.
* In the 64 bit case, it doesn't set the consistent mask.
* In the 32 bit case, the error check is backwards!
It likely will only be visible as a bug on 64 bit platforms.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Separate out sata_print_link_status() from __sata_phy_reset().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Somewhat cleaner in the resync as someone cleaned up the pio xfer users
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
sizeof() return is not an int, so use max_t to get the types right.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Be more careful about transmit locking, this solves a possible race
between tx_complete and transmit, that would cause a tx timeout.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Don't need to inline quite so many routines, let the compiler
decide
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Make sure and rate limit all the error messages that might occur. If a problem
occurs then a few messages are enough.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Small optimization, if dma addresses are 32 bits, then high
bits are always zero.
Signed-off-by: Stephen Hemminger <shemminger@osdl.or>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Don't need to zero out the status ring entries after processing.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Be more careful about memory barriers. The only place we really
need them is before and after updating the chip's ring interface.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fix problems with Yukon FE rev 2 chipset. Don't cut and paste bugs in from
sk98lin driver. Change how the ram buffer is divided up, and make the math
clearer. Also, set the thresholds where rx takes precedence. The threshold
values are just guesses at this point, it might be worth tuning them later.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Need to call pci_set_consistent_dma_mask in the case of 64 bit
DMA.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Need to make sure that sky2 receive buffers are 64 bit
aligned. Also, don't need to start off with GFP_ATOMIC
on initial setup.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
e100: e100 whitespace fixes
These are whitespace only fixes.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
e100: Handle the return values from pci_* functions
This is to resolve warnings during compile time.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
e100: Fix TX hang and RMCP Ping issue (due to a microcode loading issue)
Set the end of list bit to cause the hardware's transmit state machine to
work correctly and not prevent management (BMC) traffic.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
sbusfb_compat_ioctl() needs to return int, not long, as that
is what the fb_ops->fb_compat_ioctl method prototype wants.
Need to git rid of the "struct file *file" first argument to
fbiogetputcmap() and fbiogscursor() to match calls done in
sbusfb_compat_ioctl().
Signed-off-by: David S. Miller <davem@davemloft.net>
this patch changes if() BUG(); constructs
in iommu.c to BUG_ON(); so it gets save
to define BUG() and BUG_ON() to nullstatements.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure a consistent value is read from the STICK register by ensuring
that both high and low are read without high changing due to a roll
over of the low register.
Various Debian/SPARC users (myself include) have noticed problems with
Hummingbird based systems. The symptoms are that the system time is
seen to jump forward 3 days, 6 hours, 11 minutes give or take a few
seconds. In many cases the system then hangs some time afterwards.
I've spotted a race condition in the code to read the STICK register.
I could not work out why 3d, 6h, 11m is important but guess that it is
due to the 2^32 jump of STICK (forwards on one read and then the next
read will seem to be backwards) during a timer interrupt. I'm guessing
that a change of -2^32 will get converted to a large unsigned
increment after the arithmetic manipulation between STICK,
nanoseconds, jiffies etc.
I did a test where I modified __hbird_read_stick to artificially
inject rollover faults forcefully every few seconds. With this I saw
the clock jump over 6 times in 12 hours compared to once every month
or so.
Signed-off-by: Richard Mortimer <richm@oldelvet.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This replaces a memcmp() with is_zero_ether_addr().
Signed-off-by: Kris Katterjohn <kjak@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/cassini.c:1930: warning: long unsigned int format, different type arg (arg 4)
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This replaces some tests with is_zero_ether_addr(), memcmp(one, two,
6) with compare_ether_addr(one, two), and 6 with ETH_ALEN where
appropriate.
Signed-off-by: Kris Katterjohn <kjak@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
I misread the spec when doing the original. I've tested the corrected
version with pre UDMA drives and it now picks the right modes. This is a
specific bug fix rather than an update or new feature item.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
