Add documentation for the SM501 in Documentation/SM501.txt outlining the SM501
driver.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ensure that the M1XCLK and MCLK are sourced from the same PLL (and refuse to
bind the driver if they are not).
Update the PCI to safe initialisation values, as 72MHz is the maximum clock
for 33MHz PCI bus mastering.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The order of the set and mask operation in sm501_init_reg() was setting and
then masking the bits set. Correct the order so that we do not end up with
288MHz SDRAM clocks on certain systems.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This init sequence of setting the SDRAM clock before the bus clock is
recommend by Silicon Motion to stop problems with writes not sticking into
registers.
Signed-off-by: Vincent Sanders <vince@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds support for suspending the core (mfd driver) of the SM501.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Recently my console UTF-8 patch went mainline. Here is an additional patch
that fixes two nasty issues and improves a third one, namely:
1. My patch changed the behavior if a glyph is not found in the Unicode
mapping table. Previously for Unicode values less than 256 or 512 the
kernel tried to display the glyph from that position of the glyph table,
which could lead to a different accented letter being displayed. I
removed this fallback possibility and changed it to display the
replacement symbol.
As Behdad pointed out, some fonts (e.g. sun12x22 from the kbd package)
lack Unicode mapping information, hence all you get is lots of question
marks. Though theoretically it's actually a user-space bug (the font
should be fixed), Behdad and I both believe that it'd be good to work
around in the kernel by re-introducing the fallback solution for ASCII
characters only. This sounds a quite reasonable decision, since all fonts
ship the ASCII characters in the first 128 positions. This way users
won't be surprised by lots of question marks just because s/he issued a
not-so-perfectly parameterized setfont command. As this fallback is only
re-introduced for code points below 128, you still won't see an accented
letter replaced by another, but at least you'll always get the English
letters right.
2. My patch introduced "question mark with inverted color attributes" as a
last resort fallback glyph. Though it perfectly works on VGA console, on
framebuffer you may end up with question marks that are highlighed but
shouldn't be, and normal characters that are accidentally highlighed.
This is caused by missing FLUSHes when changing the color attribute.
3. I've updated the table of double-width character based on Markus's
updated version. Only ten new code poings (one interval) is added.
Signed-off-by: Egmont Koblinger <egmont@uhulinux.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When a namespace is unshared, a refcount on the previous nsproxy is
abusively taken, leading to a memory leak of nsproxy objects.
Signed-off-by: Cedric Le Goater <clg@fr.ibm.com>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Always disable/enable interrupts in the acpi idle routine,
even in the error path.
This is required as the 2.6.20 change in git commit d331e739f5ad2aaa9...
"Fix interrupt race in idle callback" expects the idle handler
to enable interrupt before returning.
There was a case in acpi idle routine, in which interrupt was not being
enabled before return, which caused the system to hang at bootup, while
enabling C-states on an SMP system.
The signature of the hang was that "processor.nocst"
was required to enable boot.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Update defconfigs for ATNGW100 and ATSTK1002. This will enable the
SLUB allocator by default on both, and will enable NFS root on
ATSTK1002 (ATNGW100 had it enabled before.)
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
The current at32ap7000 platform devices aren't declared as supporting DMA,
so that layered drivers can't tell whether they need to manage DMA.
This patch makes all those platform devices report that they support DMA.
Most do, but in a few cases this is inappropriate.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
USART mapping used to be accomplished by the manual filling of
at32_usart_map[] and at32_nr_usarts. This has now been replaced
with at32_map_usart() so we can remove these variables.
Signed-off-by: Ben Nizette <ben.nizette@iinet.net.au>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
If (start + size) is not cacheline aligned and (start & mask) > (end &
mask), the last but one cacheline won't be invalidated as it should.
Fix this by rounding `end' down to the nearest cacheline boundary if
it gets adjusted due to misalignment.
Also flush the write buffer unconditionally -- if the dcache wrote
back a line just before we invalidated it, the dirty data may be
sitting in the write buffer waiting to corrupt our buffer later.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Previously a program could switch to a compat mode segment and then
execute SYSCALL and it would jump to an uninitialized MSR and crash
the kernel.
Instead supply a dummy target for this case.
Pointed out by Jan Beulich
Cc: jbeulich@novell.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Include PPC_MAC in the default too, not only MAC which only covers
m68k MACs.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It is only used for PAE kernels in set_64bit.
The problem is that due to a old Windows bug many CPUs need magic MSRs
to enable CMPXCHG64, and we can't do that nicely early enough before
it is potentially used.
But since we only need it in PAE kernels so only force the checking
for CMPXCHG65 with PAE.
This fixes a boot failure on Transmeta Crusoe
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/cooloney/blackfin-2.6:
Blackfin arch: add proper const volatile to addr argument to the read functions
Blackfin arch: Add definition of dma_mapping_error
Blackfin arch: move cond_syscall() behind __KERNEL__ like all other architectures
Blackfin arch: match kernel startup messaage with new linker script
Blackfin arch: add missing braces around array bfin serial init
Blackfin arch: update printk to use KERN_EMERG and reformat crash output
Blackfin arch: update ANOMALY handling
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/mlx4: Correct max_srq_wr returned from mlx4_ib_query_device()
IPoIB/cm: Remove dead definition of struct ipoib_cm_id
IPoIB/cm: Fix interoperability when MTU doesn't match
IPoIB/cm: Initialize RX before moving QP to RTR
IB/umem: Fix possible hang on process exit
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[AF_RXRPC]: Return the number of bytes buffered in rxrpc_send_data()
[IPVS]: Fix state variable on failure to start ipvs threads
[XFRM]: Fix MTU calculation for non-ESP SAs
Do not mark the kernel text read only if KPROBES is in the kernel;
kprobes needs to hot-patch the kernel text to insert it's
instrumentation.
In this case, only mark the .rodata segment as read only.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Tested-by: S. P. Prasanna <prasanna@in.ibm.com>
Cc: Andi Kleen <ak@suse.de>
Cc: William Cohen <wcohen@redhat.com>
Cc: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
posix-timers which deliver an ignored signal are currently rearmed in
the timer softirq: This is necessary because the timer needs to be
delivered again when SIG_IGN is removed. This is not a problem, when
the interval is reasonable.
With high resolution timers enabled one might arm a posix timer with a
very small interval and ignore the signal. This might lead to a
softirq starvation when the interval is so small that the timer is
requeued onto the softirq pending list right away.
This problem was pointed out by Jan Kiszka. Thanks Jan !
The correct solution would be to stop the timer, when the signal is
ignored and rearm it when SIG_IGN is removed. Unfortunately this
requires modification in sigaction and involves non trivial sighand
locking. It's too late in the release cycle for such a change.
For now we just keep the timer running and enforce that the timer only
fires every jiffie. This does not break anything as we keep the
overrun counter correct. It adds a little inaccuracy to the
timer_gettime() interface, but...
The more complex change is necessary anyway to fix another short
coming of the current implementation, which I discovered while looking
at this problem: A pending signal is discarded when SIG_IGN is set. In
case that a posixtimer signal is pending then it is discarded as well,
but when SIG_IGN is removed later nothing rearms the timer. This is
not new, it's that way since posix timers have been merged. So nothing
to worry about right now.
I have a working solution to fix all of this, but the impact is too
large for both stable and 2.6.22. I'm going to send it out for review
in the next days.
This should go into 2.6.21.stable as well.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Jan Kiszka <jan.kiszka@web.de>
Cc: Ulrich Drepper <drepper@redhat.com>
Cc: Stable Team <stable@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nicolas Ferre reports oops from flush_dcache_page() on ARM when using
SLUB: which reuses page->mapping as page->slab. The page_mapping()
function, used by ARM and PA-RISC flush_dcache_page() implementations,
must not confuse SLUB pages with those which have page->mapping set.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add special-case handling for "handle_interruption" so that we can rewind
past the interruption. This is useful for seeing what caused a BUG() or
WARN_ON(); otherwise the unwind stops at the interruption.
Signed-off-by: Randolph Chung <tausq@debian.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
The unwinder was broken by the shift of PAGE_OFFSET in order to increase the
size of the vmalloc area on 64-bit kernels.
Signed-off-by: Randolph Chung <tausq@debian.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Function expand_upwards() did not guarded against wrapping
around to address 0. This fixes the adjtimex02 testcase from
the Linux Test Project on a 32bit PARISC kernel.
[expand_upwards is only used on parisc and ia64; it looks like it does
the right thing on both. --kyle]
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
We need to keep a spare entry in the SRQ so that there always is a
next WQE available when posting receives (so that we can tell the
difference between a full queue and an empty queue). So subtract 1
from the value HW gives us before reporting the limit on SRQ entries
to consumers.
Found by Mellanox QA.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
IPoIB connected mode currently rejects a connection request unless the
supported MTU is >= the local netdevice MTU. This breaks
interoperability with implementations that might have tweaked
IPOIB_CM_MTU, and there's real no longer a reason to do so: this test
is just a leftover from when we did not tweak MTU per-connection. Fix
this by making the test as permissive as possible.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix a crasher bug in IPoIB CM: once a QP is in the RTR state, a
receive completion (or even an asynchronous error) might be observed
on this QP, so we have to initialize all of our receive data
structures before moving to the RTR state.
As an optimization (since modify_qp might take a long time), the
jiffies update done when moving RX to the passive_ids list is also
left in place to reduce the chance of the RX being misdetected as
stale.
This fixes bug <https://bugs.openfabrics.org/show_bug.cgi?id=662>.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If ib_umem_release() is called after ib_uverbs_close() sets context->closing,
then a process can get stuck in a D state, because the code boils down to
if (down_write_trylock(&mm->mmap_sem))
down_write(&mm->mmap_sem);
which is obviously a stupid instant deadlock. Fix the code so that we
only try to take the lock once.
This bug was introduced in commit f7c6a7b5 ("IB/uverbs: Export
ib_umem_get()/ib_umem_release() to modules") which fortunately never
made it into a release, and was reported by Pete Wyckoff <pw@osc.edu>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
After i915 chip, GMCH has no AGP port. Origin bridge driver in device
table will try to access illegal regs like APBASE, APSIZE, etc. This
may cause problem.
So mark them as NULL in the table, we won't load if no IGD got detect
and bridge has no AGP port.
Signed-off-by: Wang Zhenyu <zhenyu.z.wang@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
update lists for 533, 537, and add SSYNC workaround into assembly files.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
fix module_param mistake in it821x
ahci: fix PORTS_IMPL override
kerneldoc fix in libata
libata: more NONCQ devices
pata_it821x: (partially) fix DMA in RAID mode
PATA: Add the MCP73/77 support to PATA driver
The attached patch fixes a trivial
mistake in a MODULE_PARAM_DESC of pata_it821x
driver. The parameter name in MODULE_PARAM_DESC
should match the one in module_param_named.
Signed-off-by: Stas Sergeev <stsp@aknet.ru>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If PORTS_IMPL register is zero, ahci initialize it to full mask
corresponding to nr_ports in the CAP register. hpriv->cap, which is
initialized at the end of the function, is incorrectly used as value
of CAP causing ahci to always override PORTS_IMPL to 0x1 if it's zero.
Fix it.
This fixes a bug where early ich6 ahci can only access the first port.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix parameter name from ata_dev_reread_id() in libata-core.c for kerneldoc.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
More for the NCQ blacklist. One hitachi and one raptor. Other
members of these families of drives are already on the list, so no
surprises.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Code intended to check DMA status was checking DMA command register.
Moreover firmware seems to "forget" to set DMA capable bit for the
slave device (at least in RAID mode but without ITE RAID volumes) so
check device ID for DMA capable bit when deciding whether to use DMA
and remove DMA status check completely.
Thanks to Pavol Simo for the bugreport and testing the initial fix.
This change unfortunately still doesn't fix DMA in RAID mode (which
works fine with IDE it821x) but Alan is working on the missing pieces
(pata_it821x vs libata EH issues).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Alan Cox <alan@redhat.com>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add the MCP73/MCP77 support to PATA driver.
The patch base on kernel 2.6.22-rc4
Signed-off-by: Peer Chen <peerchen@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
