When "Auto Grid" is checked in "Settings->General" UDP messages of
type "Location" will update a temporary DE grid square. The intent is
to allow an external application joining the WSJT-X UDP message
protocol to dynamically update the DE grid during mobile operation.
This change also tidies up some outstanding issues around logging the
operator call.
This change adds a new UDP message "Logged ADIF" that is emitted in
parallel with "QSO Logged" messages. The new message is valid ADIF
file format and contains the logged QSO fields. The intent is that
basic UDP server applications might already have ADIF log record
capture capabilities and could use this message to feed existing ADIF
parsing routines to log QSOs. All that should be needed is to identify
this message type and the single field is ADIF compatible ASCII.
Thanks to Brian, N9ADG, for the patches that lead to these
enhancements.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@8454 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Operator callsign is sent to DIF log if not empty.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@8267 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Measure check box added to FreqCal mode, check to record to fmt.all
with current calibration correction disabled, uncheck to see the
impact of the current calibration parameters.
The fmt.all file is now optionally renamed to fmt.bak when a
calibration solution is accepted. This allows users to preserve an
fmt.all file that they might have edited for best fit.
A calibration procedure might proceed thus:-
1) select FreqCal mode,
2) step through suggested calibration test frequencies deleting those
that have no usable signal,
3) enable "Menu->Tools->Execute frequency calibration cycle" and check
that suitable signals are present,
4) select a suitable FTol and T/R period,
5) check "Measure" and let the cycle complete a few times to gather
data,
6) uncheck "Measure" to complete the data capture, optionally tidy the
fmt.all file with your favourite editor,
7) push "Menu->Tools->Solve for calibration parameters" and accept if
you like what you see,
8) sit back and admire your accurately frequency calibrated station.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@8167 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
1. Checkbox "Double-click on call sets Tx and Rx freqs" has been removed
from the Settings -> General tab.
2. Checkbox "Lock Tx Freq" on main window is relabled "Hold Tx Freq".
3. Behavior now defaults to the "simplex" behavior in use up to code
revision r8123. In particular, double-clicking on decoded mesages
that do not contain your own call moves both Rx and Tx frequencies.
If the first callsign is your own call, only Rx freq moves.
4. If "Hold Tx Freq" is checked, double-clicking on decoded messages
moves the Rx frequency; Tx frequency is moved only if CTRL was held
down.
5. Clicking on the waterfall moves Rx and Tx frequencies as before:
Rx only on a simple click, Tx only on SHIFT-click, and both on
CTRL-click. This happens even if "Hold Tx Freq" is checked (which
is why this box is no longer labeled "Lock Tx Freq").
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@8146 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Working frequencies can be for all regions or for individual IARU
regions. This allows each mode band tuple to have one or more working
frequencies which can include local ones only offered when the user
configures their IARU region.
Change working frequency default suggestions to better fit in
FT8. General rule is FT8 is at JT65 -2kHz except where that is not
possible e.g. where that would fall into a segment not allocated for
narrow band data modes. For tight bands like top band sqeeze existing
JT65 and JT allocations to allow space for FT8.
NOTE: this change changes the WSPR frequency on 80m to allow access to
JA stations that currently have no allocation where it was placed.
ALSO NOTE: the JT65 and JT9 frequencies for 80m move down 6 kHz, again
to accommodate region 3 users. Other appliactions not within our
control should be asked to move in step when 1.8.0 is released.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7810 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Because Commander queues up CAT commands the timing of Tx audio was
not being correctly synchronized to the rig PTT. This change polls the
rig PTT state after changing PTT and waits for it to go to the
expected state. As it happens, just doing a query does most of the
synchronization as the query gets queued behind the PTT directive
within Commander, with the reply being delayed until the query
completes. This change goes further and checks the PTT state changes
within one second.
Note that users using Commander will should not suffer from ALC
overshoot issues on rigs that suffer such a problem since Tx audio now
only commences after the rig has switched to transmit. Users with
hardware sequencers may need to adjust their "Settings->Advanced->Tx
Delay" parameter, this change does not introduce any new timing hazard
but there may be a slight lengthening of the delay to Tx audio if the
rig reports PTT via CAT as the audio delay may now be timed from the
actual PTT on the rig rather than the assertion of RTS/DTR.
Still outstanding is the slow processing of Commander CAT requests
which can cause considerable delays before Tx audio can start.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7764 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
When using split operating and/or rig mode setting there is a delay
before PTT is asserted while the CAT commands are processed. There
will even be a small delay if CAT is only used for PTT. This change
waits for these commands to be completed before starting the user Tx
delay specified in the settings.
There is a notable exception to this in that DX Lab Suite Commander
does not give us a way of knowing when CAT commands have actually been
completed. This combined with the way that Commander spaces CAT
commands, rather than being paced by the rig's CAT responses, means
that delays of more than 1 second are likely. As most rigs suffer some
sort of ALC overshoot when PTT is asserted with audio already present,
it is strongly recommended not to use the DX Lab Suite Commander as a
rig control proxy if your rig may suffer ALC overshoot and you use an
external PA. Please note that using a typical RF power meter to detect
ALC overshoots is unwise as they are rarely fast enough. It is
probably wise to assume that all rigs suffer ALC overshoot since it is
very difficult to design an ALC loop that avoids it.
This change also increases the range of the "Settings->Advanced->Tx
Delay" spin box to 0s up to 2s.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7756 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Remove redundant layout on Audio tab and used layout managers on
Colors tab.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7611 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
This builds on the static phase compensation in the MSK144 decoder and
the phase analysis and polynomial fitting capabilities also in teh
MSK144 decoder, by allowing captured data to be selected for phase
equalization from the WSJT-X UI.
Reads captured phase compensation curve estimate files containing
fitted polynomial coefficients and measured phase data from MSK144
receptions. Intent is to select a compensation curve that is from a
known transmitter like an SDR which have good phase linearity. Phase
plots and compensation polynomials may be viewed and compared with the
current compensation polynomial. A suitable polynomial can be applied
to be use in all further decoding of MSK144 signals.
Plots of the currently selected polynomial and its modified higher
order terms polynomial which is actually used in equalization (this
plot may be dropped - it is just for kicks at the moment). When a
captured phase analysis file is loaded plots of the measured phase and
the proposed best fit polynomial are shown.
Basic maintenance is also included allowing clearing and loading
captured plots and an option to revert to a flat no equalization
curve.
More to come on this as amplitude equalization is also possible, this
will probably be similar, maybe even plotted on the same graph with
dual axes for phase and amplitude. Amplitude correction from a
measured reference spectrum could be viewed and selected for
equalization for all modes. TBC...
This change also introduces the QCustomPlot 3rd party
widget. Currently this is statically linked from a qcp library built
by the WSJT-X CMake script. This will probably be migrated to a shared
object (DLL) build as a CMake external project, once some CMake script
re-factoring has been completed, which is more in line with the
QCustomPlot author's intentions. This will allow efficient reuse in
other tools shipped with WSJT-X.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7570 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
This was never strictly enforced as macros can be edited to any
length. Obviously only standard messages and free text messages less
than or equal to 13 characters can actually be sent in the slow modes.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7304 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
of power settings for Transmit and Tune. Also an interim update of
v1.7_Features.txt.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7229 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
2. Make the "MSK144 Realtime decode" checkbox invisible, in preparation for removing it entirely.
3. Always use RealTime decoding in MSK144 mode. (For now, at least, click-to-decode works as before.)
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7168 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
1. Clean up mskrtd to remove unused variables.
2. Re-instate Rx frequency spinbox in MSK144 mode to allow decoding of off-frequency signals with small FTol. Make changes needed to pass Rx Freq in to fortran routines.
3. Enable realtime decoder for testing. Auto sequence does not yet work when realtime decoding is enabled. There are probably other bugs as well.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7109 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
2. Fix failure to remember Ftol setting in MSK144 mode.
3. Remove obsolete controls from Advanced tab.
4. Add control for "x 2 Tone spacing" on Advanced tab.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@6981 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
The watchdog configuration is now a spin box of minutes with a special
first value of disabled. WSJT-X counts down minutes on the minute, if
the countdown reaches zero any attempt to transmit is aborted. The
countdown is reset by any mouse press or key press event inside the
main window or if the Tx message changes (auto sequencing).
The status bar now shows the Tx watchdog countdown if it is
active. This information is shown to the right of the progress bar
text.
The warning message boxes triggered within the GUI update routine now
no longer block the GUI updates.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@6840 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
The concept of a nominal receive and transmit frequency has been
introduced. This is used as a base frequency for Doppler correction,
frequency setting and reporting. The start up frequency is now zero
which is updated by the first rig control status report. This needs
more work to accommodate calling frequency plus working frequency
operation as is used for random MS operation etc..
The main window frequency display now shows the transmit dial
frequency while transmitting.
The mode changing logic sequence has been changed such that the rig is
correctly put into and taken out of split mode as required by the
target mode. This also avoids the "other" VFO having its frequency
changed when entering a mode that does not use split operating like
WSPR.
The main window band combo box edit may now be used to input an kHz
offset from the current MHz dial frequency. This is intended for
setting a sked or working frequency on the VHF and up bands. For
example the working frequency for 23cms might be set to 1296MHz and a
working frequency of 1296.3MHz would be selected by selecting the
23cms band with the combo box drop down list and then entering 300k
into the band combo box edit widget.
When using JT4 modes a CTRL+Click on the waterfall adjusts the nominal
frequency such that the frequency clicked on becomes the Tx and Rx
frequency using the fixed 1000Hz DF that JT4 modes use. This will
probably be extended to all QSO modes when used in VHF & up mode. This
assumes that 1000Hz is an optimal DF for both Tx and Rx and therefore
one can "net" to an off frequency, but visible on the waterfall,
caller with one click.
Improvements to OmniRig rig control including use of the serial port
control lines RTS or DTR, on the CAT serial port used by OmniRig, for
PTT control.
Incrementing transaction sequence numbers added to messages to and from
the rig control thread. This enables round trip status to be tracked
and associated with a request. For example a command that might cause
several asynchronous status updates can now be tracked in the
originating thread such that it is clear which updates are caused by
executing the request. This in turn allows updates to be held until
the request is complete i.e. the state is consistent with the results
of the request.
Messages to the rig control thread are now posted as a new state
(Transceiver::TransceiverState) object. The rig control thread tracks
requests and actions any differences between the prior requests and
the new state.
The rig control thread is now stored on the heap so that it can be
closed down and released as needed. Along with this the rig control
close down semantics are better defined avoiding some potential
deadlock situations.
If the rig is placed into split mode it will be reverted to simplex
mode when the rig connection is closed.
When using direct rig control via Hamlib, rigs that have A/B VFO
arrangements and no method to query the current VFO like many Icoms
and the Yaesu FT-817/857/897(D) series now have smarted frequency
updating requiring no VFO changes when changing the frequency. This
is particularly important when doing Tx Doppler correction to avoid
glitches.
The implementation of emulated split operating mode ("Fake It") is
simplified and improved.
A dummy Hamlib transceiver for PTT control on a separate port is no
long instantiated if CAT or VOX PTT control is selected.
The resolution and any rounding of the rig CAT frequency set and get
commands is determined automatically upon opening the rig connection.
This is needed to determine the rate of frequency updates for Doppler
tracking. It also allows the rig to be more accurately controlled.
Frequency calibration is calculated separately for the receive and
transmit frequencies.
Whether the rig modulation mode should be controlled is now a
constructor argument rather than being passed with individual rig
control requests.
Doppler shift correction is considerably enhanced with simpler
controls and much better rig control. A new mode of tracking called
"receive only" is introduced for those with rigs that cannot be QSY:ed
via CAT when transmitting. Such rigs have a Doppler correction
calculated for the middle of the next transmit period just before
transmission starts. While using Doppler tracking it is now possible
to adjust the sked frequency either using the new kHz offset feature
of the main window band combo box or by directly tuning the rig VFO
knob while holding down the CTRL key.
The astronomical data window that includes Doppler tracking control is
now opened and closed using a checkable menu item to avoid it being
accidentally closed.
Debug configuration rig control diagnostic messages now have a
facility argument for clearer and more standardized trace messages.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@6590 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
This option defaults to on but may be unchecked in settings.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@6359 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
This change allows serial control lines to be forced high or low (DTR
or RTS) while using the other (RTS, DTR) for PTT on the CAT serial
port. It is only needed for some very obscure and rare serial line
powered interfaces.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@5869 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Working frequencies are mode dependent and a reset to defaults button
has been added.
Also re-factored much of the model and item delegate code to simplify
several of the model implementations. Introduced a single routine
called from main to register the custom types with Qt.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@5453 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
The settings are a linear calibration correction for the
rig. Calibration constants are supplied as an intercept error in Hertz
and a slope error in parts per million.
The correction is applied only to the final frequencies going to and
from the radio. This means that any transverter offsets are not
corrected. This is appropriate as each transverter will have its own
error factors. Transvertor and other individual band specific errors
can only be corrected by adjusting the offset for the band.
Thanks to Mike W9MDB for an initial implementation of Joe K1JT's
suggestion. See also the WSPR documentation for details of calculating
the required calibration constants.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@5396 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
r5297 | bsomervi | 2015-04-26 17:26:54 +0100 (Sun, 26 Apr 2015) | 49 lines
Various defect repairs and ambigous behaviour clarifications
A regression introduced in v1.5.0-rc1 where PTT on an alternate serial
port when using no CAT control is resolved.
A regression introduced in v1.5.0-rc1 where the network server field
was not being restored in the settings dialog has been resolved.
In settings the "Test PTT" button is now styled by checked state.
The "Test PTT" button is enabled without needing click "Test CAT"
first when no CAT rig control is selected.
Various parts of the settings dialog are now disabled when no CAT rig
control is selected. These are the "Mode" group, the "Split Operation"
group and the "Monitor returns to last used frequency" check box. None
of these have any visible impact nor make sense without CAT rig
control.
Initialization and teardown of rig control internals has been revised
to avoid several problems related to timing and when switching between
different CAT settings. This includes improvements in having the
operating frequency restored between sessions when not using CAT rig
control.
The initialization of OmniRig connections has been improved,
unfortunately it is still possible to get an exception when clicking
the "Test CAT" button where just clicking "OK" and leaving the
settings dialog will probably work.
Some unnecessary CAT commands output during direct rig control have
been elided to reduce the level of traffic a little.
The handling of some automatically generated free text messages used
when the station is a type 2 compound callsign or is working a type 2
compound callsign has been improved. This is related to how a double
click on a message of the form "DE TI4/N0URE 73" is double
clicked. The new behaviour depends on whether the current "DX Call"
matches the call in the message. This resolves the ambiguity as to
whether this message is a sign off at the end of a QSO with current
operator (a 73 message is generated) or a tail end opportunity where
the message should be treated the same as a CQ or QRZ message (WSJT-X
QSYs to the frequency, generates messages and selects message one
ready to call). This still leaves some potential ambiguous behaviors
in this complex area but selecting "Clear DX call and grid after
logging" should resolve most of them.
Rig control trace messages have been cleaned up and are now more
helpful, less verbose and, tidier in the source code.
------------------------------------------------------------------------
Merged from the wsjtx-1.5 branch.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@5298 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Trying to resolve the best default size for the Settings window for
all platforms whilst allowing the user to shrink the window on
platforms that allow a more compact widget layout like Windows.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@5251 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
To facilitate interaction with other applications WSJT-X now sends
status updates to a predefined UDP server or multicast group
address. The status updates include the information currently posted
to the decodes.txt and wsjtx_status.txt files. An optional back
communications channel is also implemented allowing the UDP server
application to control some basic actions in WSJT-X.
A reference implementaion of a typical UDP server written in C++ using
Qt is provided to demonstrate these facilities. This application is
not intended as a user tool but only as an example of how a third
party application may interact with WSJT-X.
The UDP messages Use QDataStream based serialization. Messages are
documented in NetworkMessage.hpp along with some helper classes that
simplify the building and decoding of messages.
Two message handling classes are introduced, MessageClient and
MessageServer. WSJT-X uses the MessageClient class to manage outgoing
and incoming UDP messages that allow communication with other
applications. The MessageServer class implements the kind of code
that a potential cooperating application might use. Although these
classes use Qt serialization facilities, the message formats are
easily read and written by applications that do not use the Qt
framework.
MessageAggregator is a demonstration application that uses
MessageServer and presents a GUI that displays messages from one or
more WSJT-X instances and allows sending back a CQ or QRZ reply
invocation by double clicking a decode. This application is not
intended as a user facing tool but rather as a demonstration of the
WSJT-X UDP messaging facility. It also demonstrates being a multicast
UDP server by allowing multiple instances to run concurrently. This is
enabled by using an appropriate multicast group address as the server
address. Cooperating applications need not implement multicast
techniques but it is recomended otherwise only a single appliaction
can act as a broadcast message (from WSJT-X) recipient.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@5225 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Made the force control lines group box in the Configuration UI
checkable which allows the DTR and RTS checkboxes to mean either force
low or force high.
Also improved UI control logic to only allow valid setting
combintions. Disabled network port text edit for OmniRig. Cleared
network port combo box list for network interfaces like HRD and DXLab
Commander, was erroneously showing COM ports.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@5222 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Thanks to Sebastian W4AS for reporting these.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@5129 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Option to control standard message generation for type 2 compound
callsign holders.
Process decoded messages based on either base or full callsign for
both DE and DX callsigns.
Change CW id when callsign changed in settings.
Merged from wsjtx-1.4 branch.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@5000 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
procedure; better window functions for some FFTs, resulting in
better decoder performance; User-selectable colors for backgrounds
of decoded messages. NB: more testing is desirable!
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@4951 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Several users have reported missing parts of the Settings UI due to
the window starting up too small. This shouldn't be possible since the
Qt layout manager should expand the window but it doesn't seem to
always get it right.
Merged from wsjtx-1.4 branch.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@4627 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
On some systems or font combinations this window starts too small for
the layout to render all the widgets on the Radio tab.
Merged from wsjtx-1.4 branch.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@4482 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Some rigs either do not honour some CAT commands while transmitting or
interpret them incorrectly. To deal with this a settings option to
allow TX frequency changes while transmitting has been added with a
default value of off.
Any UI actions that directly or indirectly change the TX frequency are
guarded according to this new option. As well as this band changes and
use of the +2kHz check box are disabled and guarded respectively in
transmit mode.
Mode changes via the menu are now disabled while transmitting.
When TX frequency changes are allowed; frequency changes are correctly
implemented while in tune mode.
Double clicking decodes while transmitting now correctly regenerate
and change the message sent on the fly.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@4349 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
