Also added a new configuration query method to check if Rig is None
i.e. a dummy rig.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@6629 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Multiple configurations are accessed and maintained from a new main
window menu bar pop up menu "Configurations". The prior settings are
the "Default" entry. New configurations may be added by cloning
existing ones. Maintenance and navigation is via sub menus for each
configuration.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@6623 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Hamlib can return fractional decimal Hertz for some devices that use
internal fixed point binary registers e.g. devices using the Si570
clock generator as a frequency synthesizer. Rounding to the nearest
Hertz should ensure accurate round tripping of frequencies.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@6622 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
2. When switching to JT65 mode, go through JT9 first.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@6621 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
The changes to fix the Tx DF at 1000Hz when VHF & up features are
enabled had an undesirable side effect of disabling double clicking on
decodes because this was disabled by the Tx DF spin box being
disabled. The Tx DF spin box being disabled in VHF & up mode may
change but this change fixes this issue regardless.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@6617 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
2. Don't display orange warning bar when in WSPR mode.
3. Fix a longstanding compiler warning.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@6616 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
spectrum is -20 dB relative to 1500 Hz -- or at maximum width 240 to 4000 Hz.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@6615 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Rigs like the Icom IC-7100 have a Data drop down on the HRD UI to
switch the rig in and out and query the data modes. This change
supports that by using the On and Off selections to set and query data
mode for suitable modes (USB/LSB/FM as DIG_U/DIG_L/DIG_FM).
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@6599 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Only when split operating is not none should split be touched on the
rig, likewise only when Settings->Radio->Mode is not none should the
rig mode be touched.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@6597 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
The concept of a nominal receive and transmit frequency has been
introduced. This is used as a base frequency for Doppler correction,
frequency setting and reporting. The start up frequency is now zero
which is updated by the first rig control status report. This needs
more work to accommodate calling frequency plus working frequency
operation as is used for random MS operation etc..
The main window frequency display now shows the transmit dial
frequency while transmitting.
The mode changing logic sequence has been changed such that the rig is
correctly put into and taken out of split mode as required by the
target mode. This also avoids the "other" VFO having its frequency
changed when entering a mode that does not use split operating like
WSPR.
The main window band combo box edit may now be used to input an kHz
offset from the current MHz dial frequency. This is intended for
setting a sked or working frequency on the VHF and up bands. For
example the working frequency for 23cms might be set to 1296MHz and a
working frequency of 1296.3MHz would be selected by selecting the
23cms band with the combo box drop down list and then entering 300k
into the band combo box edit widget.
When using JT4 modes a CTRL+Click on the waterfall adjusts the nominal
frequency such that the frequency clicked on becomes the Tx and Rx
frequency using the fixed 1000Hz DF that JT4 modes use. This will
probably be extended to all QSO modes when used in VHF & up mode. This
assumes that 1000Hz is an optimal DF for both Tx and Rx and therefore
one can "net" to an off frequency, but visible on the waterfall,
caller with one click.
Improvements to OmniRig rig control including use of the serial port
control lines RTS or DTR, on the CAT serial port used by OmniRig, for
PTT control.
Incrementing transaction sequence numbers added to messages to and from
the rig control thread. This enables round trip status to be tracked
and associated with a request. For example a command that might cause
several asynchronous status updates can now be tracked in the
originating thread such that it is clear which updates are caused by
executing the request. This in turn allows updates to be held until
the request is complete i.e. the state is consistent with the results
of the request.
Messages to the rig control thread are now posted as a new state
(Transceiver::TransceiverState) object. The rig control thread tracks
requests and actions any differences between the prior requests and
the new state.
The rig control thread is now stored on the heap so that it can be
closed down and released as needed. Along with this the rig control
close down semantics are better defined avoiding some potential
deadlock situations.
If the rig is placed into split mode it will be reverted to simplex
mode when the rig connection is closed.
When using direct rig control via Hamlib, rigs that have A/B VFO
arrangements and no method to query the current VFO like many Icoms
and the Yaesu FT-817/857/897(D) series now have smarted frequency
updating requiring no VFO changes when changing the frequency. This
is particularly important when doing Tx Doppler correction to avoid
glitches.
The implementation of emulated split operating mode ("Fake It") is
simplified and improved.
A dummy Hamlib transceiver for PTT control on a separate port is no
long instantiated if CAT or VOX PTT control is selected.
The resolution and any rounding of the rig CAT frequency set and get
commands is determined automatically upon opening the rig connection.
This is needed to determine the rate of frequency updates for Doppler
tracking. It also allows the rig to be more accurately controlled.
Frequency calibration is calculated separately for the receive and
transmit frequencies.
Whether the rig modulation mode should be controlled is now a
constructor argument rather than being passed with individual rig
control requests.
Doppler shift correction is considerably enhanced with simpler
controls and much better rig control. A new mode of tracking called
"receive only" is introduced for those with rigs that cannot be QSY:ed
via CAT when transmitting. Such rigs have a Doppler correction
calculated for the middle of the next transmit period just before
transmission starts. While using Doppler tracking it is now possible
to adjust the sked frequency either using the new kHz offset feature
of the main window band combo box or by directly tuning the rig VFO
knob while holding down the CTRL key.
The astronomical data window that includes Doppler tracking control is
now opened and closed using a checkable menu item to avoid it being
accidentally closed.
Debug configuration rig control diagnostic messages now have a
facility argument for clearer and more standardized trace messages.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@6590 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Setting the CMake option WSJT_RIG_NONE_CAN_SPLIT=ON will buold a
version taht allows split operating with the dummy rig. This must not
be shipped since it will generate incorrect Tx tones.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@6589 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Hamlib now used libusb-1.0 and since that is available on Windows we
can now build with it across platforms. This change allows for that if
the custom USB backends are configured in Hamlib.
As it looks like Hamlib v3.1 will be suitable for WSJT-X this change
also puts in place what is needed to link to a Hamlib SO/DLL/DYLIB
when required. This is switched on by not defining the CMake variable
hamlib_STATIC. This could be used on Windows and Mac but Linux still
must have Hamlib statically linked due to repository versions being
too old.
For now Hamlib remains statically linked for consistency across
platforms.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@6581 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
