Because of the way logged QSO times are split and rebuilt in the QSO
logging code the UTC time specification is lost. This change sets them
back to UTC since that is what they are.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7566 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
This change is specifically to work around some surprising behaviour
in the Elecraft K3[S] which suffers audio drop outs when null changes
that might effect the internal DSP are processed. This manifests when
a blind mode change is sent through Commander. Here we read the mode
and only subsequently command a mode change if it is not what we
expect. Blind mode changes were preferred with Commander until now
since state queries through Commander are occasionally unreliable.
This issue has been reported to Elecraft so may not be permanent if
they can and will address it in the rig's firmware.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7565 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Commander queues rig control commands and can return stale or invalid
results immediately after state change commands so this change waits a
couple of seconds hoping that Commander gets around to polling the rig
before we read back the state.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7564 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
This is no longer necessary as the sample downloader now reverts to
HTTP if SSL libararies are not installed.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7563 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Older rigs like the Yaesu FT-736R only support set commands and
extremely limited query commands (like squelch and S-meter
levels). This change allows them to be supported via Hamlib albeit in
a very minimal way.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7556 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
This code was causing the JT9 decoder to fail to decode, maybe due to
high noise levels and the resulting discontinuity introduced by
zeroing out samples.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7555 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
I can't remember exactly why mode tracking was disabled but it doesn't
seem to be necessary to do so. I am expecting some fallout from this
change, when I discover why it was necessary to ignore the rig mode I
will find a better way to do this.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7548 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Fix tab order on Log QSO window. Amend message_aggregator QSOs logged
window to show both time on and time off.
Thanks to Mike W9MDB for this patch.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7532 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Allow band drop down list to be used to select FreqCal frequencies,
also resets position in automatic cycle. Tidy up some unnecessary
code.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7486 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
1. Menu item *Tools -> Execute frequency calibration cycle* is renamed and checkable. Cycling does not start until checked.
2. Ctrl+F10 now allows you to cycle manually through the list of calibration frequencies.
3. Calibration sequence lengths can be set to 5, 10, 15, or 30 s with the sbTR spinBox.
Also: don't set sbTR index to 0 when entering a slow mode.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7485 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Reduce the tolerance to +-DF in this case to avoid array bounds error.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7470 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Rx DF is now "real-time" adjusting the rig in concert with the
monitored DF.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7465 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Some default time signals have been added to the frequency list so a
base set can be obtained by resetting the frequency list,
alternatively they can be added ad hoc in the normal fashion.
FreqCal mode behavior is to select the lowest cal frequency upon
entering FreqCal mode and cycling through each cal frequency
repeatedly. Ctrl+F10 jumps directly to the next higher frequency.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7463 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Allow group separators as well as decimal points in MHz input fields
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7462 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
Deepest decode level should be selected automatically when switching
to JT4 or JT65 when VHF & up mode is on and either of averaging or
deep search are enabled.
git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@7456 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
