Bill Somerville 2b781d1685 Improved automatic message handling
More consistent and accurate processing of compund callsigns including
recognizing the  user's call  in both base  and fully  qualified form,
extracting reports  from special type  one and type two  compound call
messages.  Ensure that  "CQ DX"  message prefixes  are recognized  and
processd correctly.

The  cycle of  double  clicking through  a QSO  has  been enhanced  to
recognoize the  standard messages correctly  and use the  correct next
message. The automatic  transmission button "Enable Tx"  now does what
it says and does not double as a stop transmit button. This allows the
current transmission  to complete  even if the  automatic transmission
feature is  disabled. In line with  this the "stop sending  after a 73
message is sent"  feature turns off the  automatic transmission enable
at the start of the sending of  a 73 message and also the next message
is now set up as the CQ  message automatically in this scenario.  A 73
message is now  either a standard message containing the  word "73" or
any free text  message containing "73" (not necessarily  as a distinct
word").

git-svn-id: svn+ssh://svn.code.sf.net/p/wsjt/wsjt/branches/wsjtx@5055 ab8295b8-cf94-4d9e-aec4-7959e3be5d79
2015-03-14 19:13:18 +00:00
2015-03-14 16:21:02 +00:00
2015-03-04 13:21:41 +00:00
2014-03-30 01:31:40 +00:00
2014-12-03 00:06:54 +00:00
2014-07-21 20:25:05 +00:00
2014-11-28 23:34:23 +00:00
2014-11-28 23:34:23 +00:00
2015-03-04 13:21:41 +00:00
2015-03-04 19:21:06 +00:00
2014-11-28 23:34:23 +00:00
2012-10-21 19:24:54 +00:00
2013-08-10 15:29:55 +00:00
2014-01-30 18:40:16 +00:00
2014-12-03 00:06:54 +00:00
2014-03-30 01:31:40 +00:00
2014-11-28 23:34:23 +00:00
2015-03-14 19:13:18 +00:00
2015-03-14 19:13:18 +00:00
2014-11-28 23:34:23 +00:00
2014-04-03 19:44:34 +00:00
2014-11-28 23:34:23 +00:00
2015-03-04 13:21:41 +00:00
2015-02-11 18:20:07 +00:00
2014-10-21 14:04:37 +00:00

 __       __   ______      _____  ________      __    __ 
|  \  _  |  \ /      \    |     \|        \    |  \  |  \
| $$ / \ | $$|  $$$$$$\    \$$$$$ \$$$$$$$$    | $$  | $$
| $$/  $\| $$| $$___\$$      | $$   | $$ ______ \$$\/  $$
| $$  $$$\ $$ \$$    \  __   | $$   | $$|      \ >$$  $$ 
| $$ $$\$$\$$ _\$$$$$$\|  \  | $$   | $$ \$$$$$$/  $$$$\ 
| $$$$  \$$$$|  \__| $$| $$__| $$   | $$       |  $$ \$$\
| $$$    \$$$ \$$    $$ \$$    $$   | $$       | $$  | $$
 \$$      \$$  \$$$$$$   \$$$$$$     \$$        \$$   \$$
                                                         
                                                         
                                                         
Copyright (C) 2001 - 2014 by Joe Taylor, K1JT.

WSJT-X implements JT9, a new mode  designed especially for the LF, MF,
and  HF bands,  as well  as  the popular  mode JT65.  Both modes  were
designed for making reliable, confirmed QSOs under extreme weak-signal
conditions.  They  use nearly  identical message structure  and source
encoding.  JT65 was  designed for  EME (“moonbounce”)  on the  VHF/UHF
bands  and   has  also  proved   very  effective  for   worldwide  QRP
communication at  HF; in contrast, JT9  is optimized for HF  and lower
frequencies. JT9 is  about 2 dB more sensitive than  JT65A while using
less  than 10%  of the  bandwidth. World-wide  QSOs are  possible with
power levels of a few watts and  compromise antennas. A 2 kHz slice of
spectrum is  essentially full when  occupied by ten JT65  signals.  As
many as 100 JT9 signals can fit into the same space, without overlap.

WSJT-X offers a “bi-lingual” operating  mode in which you can transmit
and   receive  JT65   and   JT9  signals,   switching  between   modes
automatically as  needed.  Displayed  bandwidth can be  as large  as 5
kHz. If  your receiver  has as  upper-sideband filter  at least  4 kHz
wide, you can have all the typical  JT65 and JT9 activity on screen at
once, available for  making QSOs with a click of  the mouse. Even with
standard SSB-width IF filters, switching between JT65 and JT9 modes is
quick and convenient. Be sure to read the online WSJT-X User's Guide.

Project web site:

http://www.physics.princeton.edu/pulsar/K1JT/wsjtx.html

Project mailing  list (shared  with other  applications from  the same
team):

https://groups.yahoo.com/neo/groups/wsjtgroup

Description
This a mirror of WSJT-X and will be updated every 6 hours. PR will be ignored, head to the SF link. Repo will be updated at 06:00:00 UTC 12:00:00 UTC 18:00:00 UTC 00:00:00 UTC Now fixed.
Readme 216 MiB
Languages
C++ 52.4%
Fortran 19.5%
Python 18.8%
C 7.6%
CMake 1.3%
Other 0.1%